Asus TS300-E3 - Manual (Page 78)

C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n 4 - 1 0 4 - 1 0 4 - 1 0 4 - 1 0 4 - 1 0
2 . 2 . 2 . 2 . 2 . P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E 1 ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E 1 ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E 1 ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E 1 ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E 1 )
This connector is for an Ultra ATA100/66/33 signal cable. The Ultra
ATA 100/66/33 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for an
Ultra ATA 100/66/33 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra ATA 100/66/33 IDE master device
(hard disk drive). If you install two hard disk drives, you must configure
the second drive as a slave device by setting its jumper accordingly.
Refer to the hard disk documentation for the jumper settings.
4.3 Internal connectors
1 . 1 . 1 . 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 )
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using a FDD cable with a covered Pin 5.
• Pin 20 on the IDE connector is removed to match the covered hole on
the Ultra ATA cable connector. This prevents incorrect insertion when
you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra ATA 100/66/33 IDE devices.
LAN2
®
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
P5MT Series Floppy disk drive connector
FLOPPY1
PIN 1
LAN2
®
P5MT Series IDE connector
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE1
PIN 1