KROHNE CORIMASS E Series EN - Manual (Page 30)

30
5.2 Krohne Operating Concept
1.5.0 ALARM OUT A
1.0 OPERATION 1.1.1 - 1.1.4
1.2.1 - 1.2.7
1.3.1 - 1.3.3
1.4.1 - 1.4.3
1.5.1 - 1.5.3
1.1.0 BASIS.PARAM.
1.2.0 DISPLAY
1.3.0 CURRENT OUT I
1.4.0 PULS.OUTP.P
2.0 TEST
2.5 TEST INP.E
2.1 TEST DISP
2.2 TEST I
2.3 TEST P
2.4 TEST A
2.6 TEST TEMP
2.7.0 TEST.PRIMRY 2.7.1 - 2.7.4
3.5.0 ALARM.OUT.A
3.1.0 BASIS.PARAM
3.2.0 DISPLAY
3.3.0 CURRENT.OUT I
3.4.0 PULS.OUTP.P
3.6.0 CTRL.INP.E
3.7.0 SYS.CTRL.S
3.8.0 USER DATA
3.9.0 TUBE PARAMS
3.0 INSTALL
3.1.1 - 3.1.8
3.2.1 - 3.2.8
3.3.1 - 3.3.4
3.4.1 - 3.4.4
3.5.1 - 3.5.4
3.6.1 - 3.6.2
3.7.1 - 3.7.4
3.8.1 - 3.8.8
3.9.1 - 3.9.11
4.0 PARAM.ERROR
4.5 not used
4.1 not used
4.2.0 CURRENT.OUT. I
4.3.0 ZERO SET
4.4 not used
4.6.0 PULS.OUTP.P
4.7.0 PROC.ALARM
4.8.0 SYSTEM.CTRL
4.2.1 - 4.2.2
4.3.1 - 4.3.2
4.6.1 - 4.6.2
4.7.1 - 4.7.2
4.8.1 - 4.8.2
P
R
OGRAMMI
N
G
L
EVEL
P
ARAMETER CH
ECK
L
EVEL
↵ ↑ →
210.50
kg/min
Measuring Mode
STATUS.LIST.
RESET TOTAL
Code 2
Error List
RESET YES
RESET NO
QUIT YES
QUIT NO
R
ESET
/
QU
IT
→ Code 1
- - - - - - - When this display appears, press entry code 1.
See Fct. 3.8.2 and 3.8.3. Factory setting:
→ → → ↑ ↑ ↑ ↵ ↵ ↵
↑
Submenu
Select with Key
↑
Main Menu
Select with Key
↑
Function
Select with Key
↑
Data Input
with Keys
↵ →
→ → →
↵ ↵
↵
↵
Param. Check
and return to
measurement
mode
Split functions
of keys between
main and
submenus.
The blinking
part of the
display (cursor)
that may be
changed is
in bold
When in
RESET/QUIT
and programming
modes, outputs
remain active,
measuring
normally, except
in 2.0 TEST menu
when output is
being tested, and
when zeroing
flowmeter - 3.1.1
and 1.1.1 -
MEAS.VALUE