KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.48 to 3.04 - Manual (Page 169)

BOP-1K 101509
B-19
B.71 [SOURce:]LIST:SET:TRIGger? QUERY
LIST:SET:TRIG?
Syntax: Short Form: LIST:SET:TRIG? Long Form: LIST:SET:TRIGger?
Returns = trigger pulse-width between 0.00025 and 0.034 second
Description: Returns trigger pulse-width. If trigger pulse duration has not been set, error 100- “command error”
results .
B.72 [SOURce:]LIST:SET:WAIT COMMAND
LIST:SET:WAIT
Syntax: Short Form: LIST:SET:WAIT value
Long Form: LIST:SET:WAIT value
where:
= time-out for a wait command between .00025 and .034 seconds
Description: Establishes the time-out for a wait command. If this command is not sent, the time out period will
be 0 indicating an infinite wait time. (See Figures B-6 and B-7.)
B.73 [SOURce:]LIST:SET:WAIT? QUERY
LIST:SET:WAIT?
Syntax: Short Form: LIST:SET:WAIT? Long Form: LIST:SET:WAIT?
Returns = time-out for a wait command between 0.00025 and 0.033 second
Description: Returns the time-out for a wait command. Returns 0 if LIST:SET:WAIT not sent, indicating infinite wait
time.
B.74 [SOURce:]LIST:TRIGger COMMAND
LIST:TRIG
Syntax: Short Form: LIST:TRIG
Long Form: LIST:TRIGger
where:
= programmed current (Amps) for current list, or programmed voltage (Volts) for voltage list.
Description: Similar to LIST:VOLT or LIST:CURR, except also allows Output Off flag of External Protection
Port to be used to trigger an external device. In addition to setting the output to the speci-
fied (for duration established by LIST:SET:TRIG), causes the Output Off flag transistor (EXT_E, pin 5,
and EXT_C, pin 6, of the External Protection port) to be set to the state (on or off) for the duration set
by the LIST:SET:TRIG command.
If the trigger duration is not established by the LIST:SET:TRIG command, a -221 “Settings conflict”
error results. This command must be preceded by LIST:CURR or LIST:VOLT command, otherwise a -
221 “Settings conflict” error results. The entries on the dwell list must match the values on the current
or voltage list, otherwise a -226 “Lists Not Same Length” error results. (See Figure B-7.)
B.75 [SOURce:]LIST:VOLTage COMMAND
LIST:VOLT
Short Form: LIST:VOLT[:LEV] , , . . . (to max of 5900 data points)
Long Form: LIST:VOLTage[:LEVel] , , . . . (to max of 5900 data points)
= digits with decimal point and Exponent, e.g., 2.71E1 for 27.1
Description: Adds the voltage value (in Amps) to list. This command sequentially adds LIST:VOLTage values to
the main channel List Data Table locations illustrated in Table B-2. LIST:CLE sets starting location to 0.
Next location indicated by LIST:VOLT:POIN? The maximum number of entries is 2950, 3933, or 5900.
Since the input buffer of the BOP has a limit of 253 characters, multiple commands are necessary to
complete the full 5900 entries of the list. If LIST:CURR has any entries, an error message: -221,"Set-
tings conflict" is posted in the error queue. Related Commands: LIST:VOLT:POIN?, FUNC:MODE,
LIST:CLE, *RST. (See example, Figure B-5.)
B.76 [SOURce:]LIST:VOLTage? QUERY
LIST:VOLT?
Syntax: Short Form: LIST:VOLT? Long Form: LIST:VOLTage?
Return Value: , , . . . to
Description: Identifies the parameters (main channel) entered for the list. Starting at location established by
LIST:QUERy, returns comma-separated list of up to 16 values indicating the main channel parameters
entered. i.e., the contents of the main channel locations of Table B-2. Related Commands: LIST:
VOLT, LIST:QUERy. If LIST:CURR has any entries, an error message: -221,"Settings conflict" is
posted in the error queue. (See example, Figure B-5.)