KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.48 to 3.04 - Manual (Page 130)

4-2
BOP-1K 101509
Remote Calibr.
VOLTAGE
EXTERNAL
PROTECTION,
Pos. Voltage
Neg. Voltage
(together) 1. ZERO
2. POSITIVE External:
1. 0.0V
2. +10.0V
(Analog I/O Port
pin 14+6 ref to
pin12) N/A No requirements 1. Automatic internal
measurement
2. Remote Calibration
only.
CURRENT,
INTERNAL 1. ZERO
2. POSITIVE
3. NEGATIVE Internal Output Current:
1. 0.0A
2. +Current FS
3. –Current FS Short with Meas.
Shunt
Automatic CM 1. DVM between probe
terminals of Meas.
Shunt (LO towards
COM S)
2. Adjust for zero, posi-
tive and negative FS
CURRENT,
PROTECTION 1. POSITIVE
2. NEGATIVE Internal Output Current:
1. +Current FS
2. -Current FS Short with Meas.
Shunt
Automatic VM 1. DVM between probe
terminals of Meas.
Shunt (LO towards
COM S)
2. Adjust for positive
and negative FS.
CURRENT,
EXTERNAL 1. ZERO
2. POSITIVE External:
1. 0.0V
2. +10.0V
(Analog I/O Port
pin 11 ref to 4) Output Current:
1. 0.0A
2. +Current FS Short with Meas.
Shunt
Automatic CM 1. DVM between probe
terminals of Meas.
Shunt (LO towards
COM S).
2)Adjust for zero, pos
FS.
CURRENT,
GAIN 1. ZERO
2. POSITIVE External:
1. 0.0V
2. +10.0V
(Analog I/O Port
pin 11 ref to 4) Output Current:
1. 0.0A
2. 0.0A Short with Meas.
Shunt
Automatic CM 1. DVM between probe
terminals of Meas.
Shunt (LO towards
COM S)
2. Adjust for zero
(both Zero and Positive)
EXTERNAL
CONTROLS,
PARALLEL 1. ZERO
2. POSITIVE External:
1. 0.0V
2. +10.0V
(Par/Ser CTRL-IN
Port pin3 ref. to
pin1) Output Current:
1. 0.0A
2. +Current FS Short with Meas.
Shunt
Automatic CM 1. DVM between probe
terminals of Meas.
Shunt (LO towards
COM S)
2. Adjust for zero, pos.
FS
3. Calibrate unit for
Slave in Parallel
EXTERNAL
CONTROLS,
I_OUT 1. ZERO
2. POSITIVE INTERNAL Voltage at Par/Ser
CTRL-IN Port pin 6
ref. to pin1:
1. 0.0V
2. +10.0V Short with Meas.
Shunt
Automatic CM 1. DVM at Par/Ser
CTRL-IN Port pin 6 ref.
to pin 1
2. Adjust for zero,
+10.0V
3. Calibrate unit for
Master in Parallel
Remote Calibr.
CURRENT
EXTERNAL
PROTECTION,
Pos. Current
Neg. Current
(together) 1. ZERO
2. POSITIVE External:
1. 0.0V
2. +10.0V
(Analog I/O Port
pins 13, 5 ref to
pin 12) N/A No requirements 1. Automatic internal
measurement
2. Remote Calibration.
only.
TABLE 4-1. CALIBRATION SUMMARY (CONTINUED)
Type Step
Reference Type
and Value
Monitored
Parameter
Output Conditions Notes