KEPCO BIT 4882F - Manual (Page 6)

ii
BIT 4882 SVC 030507
TABLE OF CONTENTS
SECTION PAGE
APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-2
A.5 *ESR? — Event Status Register Query.................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-2
A.9 *RST — Reset Command....................................................................................................................... A-2
A.10 *SRE — Service Request Enable Command ........................................................................................ A-3
A.11 *SRE? — Service Request Enable Query .............................................................................................. A-4
A.12 *STB? — Status Byte Register Query ................................................................................................... A-4
A.13 *TRG — Trigger Command ................................................................................................................... A-4
A.14 *TST? — Self Test Query ....................................................................................................................... A-4
A.15 *WAI — Wait-To-Continue Command .................................................................................................... A-4
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 INITiate[:IMMediate] Command.............................................................................................................. B-1
B.3 INITiate:CONTinuous Command............................................................................................................ B-1
B.4 INITiate:CONTinuous Query................................................................................................................... B-1
B.5 MEASure[:SCALar]:CURRent[:DC]? Query ........................................................................................... B-2
B.6 MEASure:VOLTage[:SCALar][:DC]? Query ........................................................................................... B-2
B.7 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Command.......................................................... B-2
B.8 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Query................................................................. B-3
B.9 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude] Command........................................................... B-3
B.10 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]? Query................................................................ B-3
B.11 .[SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] Command......................................................... B-3
B.12 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? Query............................................................... B-3
B.13 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude] Command........................................................... B-4
B.14 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]? Query................................................................ B-4
B.15 [SOURce:]FUNCtion:MODE ................................................................................................................... B-4
B.16 STATus:OPERation:CONDition Query................................................................................................... B-4
B.17 STATus:OPEReration:ENABle Command ............................................................................................. B-4
B.18 STATus:OPEReration:ENABle? Query .................................................................................................. B-5
B.19 STATus:OPERation[:EVENt] Query ....................................................................................................... B-5
B.20 STATus:PRESet Command ................................................................................................................... B-5
B.21 STATus:QUEStionable[:EVENt]? Query ................................................................................................ B-5
B.22 STATus:QUEStionable:CONDition? Query ............................................................................................ B-5
B.23 STATus:QUEStionable:ENABle Command............................................................................................ B-6
B.24 STATus:QUEStionable:ENABle? Query................................................................................................. B-6
B.25 SYSTem:ERRor? Query......................................................................................................................... B-7
B.26 SYSTem:LANGuage Command ............................................................................................................. B-7
B.27 SYSTem:VERSion Query ....................................................................................................................... B-7
APPENDIX C - CIIL COMMAND DEFINITIONS