Brocade NetIron CER 2000 Series Hardware Guide (Supporting R05.6.00) - Manual (Page 28)

18 Brocade NetIron CES 2000 Series and NetIron CER 2000 Series Hardware Installation Guide
53-1003029-02
Hardware features
1
10-Gbps ports
The Brocade NetIron CES 2000 Series 2048C-4X, Brocade NetIron CES 2000 Series 2048F-4X,
NetIron CER 2000 Series 2048C-4X-RT, and the NetIron CER 2000 Series 2048F-4X-RT come with
four 10-Gigabit Ethernet ports installed. The four 10-Gigabit Ethernet uplink ports support
10-Gigabit Small Form Factor Pluggable (SFP+) MSA-compliant optical transceivers
The Brocade NetIron CES 2000 Series 2048CX, Brocade NetIron CES 2000 Series 2048FX,
NetIron CER 2000 Series 2048CX, and the NetIron CER 2000 Series 2048FX come with two
10-Gigabit Ethernet ports installed. A 24-port Brocade NetIron CES 2000 Series,NetIron CER 2000
Series has a slot to accommodate a 2-port 10-Gigabit Ethernet module. If your 24-port device does
not include a 10-GbE module, you can optionally install one. Refer to
“10-Gigabit Ethernet module
installation or replacement” on page 80. The two 10-Gigabit Ethernet ports use 10-Gigabit Small
Form Factor Pluggable (XFP) MSA-compliant transceivers.
Supported optics
100/1000 Ethernet Ports
The Ethernet Interface module contains 24 or 48 physical ports, through which you can connect
your device to other network devices at a speed of 100 Mbps or 1 Gbps.
Into a physical port, you must insert a fiber-optic transceiver provided by Brocade. The
SFP-compliant fiber-optic modules provide an optical transceiver or physical medium-dependent
(PMD) interface for fiber that can be used with the LAN physical layer (PHY)
The following 100 Mbps and 1 GbE optical transceivers are available from Brocade:
TABLE 5 SFP-compliant transceivers for the 100/1000 Ethernet interface module
Part number Description
E1MG-TX SFP Copper, RJ-45 connector
E1MG-SX 1000Base-SX SFP optic, multi-mode fiber, LC connector
E1MTG-SX 1000Base-SX SFP optic, multi-mode fiber, MTRJ connector
E1MG-SX2-1310 1310 1000Base-SX SFP optic multi-mode fiber, LC connector and support for distances
up to 2km
E1MG-LX 1000Base-LX SFP optic, single-mode fiber, LC connector
E1MG-LHA 1000Base-LHA SFP optic, single-mode fiber, LC connector
E1MG-LHB 1000Base-LHB SFP optic, single-mode fiber, LC connector, 150km Maximum Reach
E1MG-BXD 1000Base-BXD SFP optic single-mode fiber, 1490nm, LC connector.
This optic can only be connected to an E1MG-BXU
E1MG-CWDM80-1470 CWDM SFP optic, 80km, 1470nm, LC connector
E1MG-CWDM80-1490 CWDM SFP optic, 80Km, 1490nm, LC connector
E1MG-CWDM80-1510 CWDM SFP optic, 80Km, 1510nm, LC connector
E1MG-CWDM80-1530 CWDM SFP optic, 80Km, 1530nm, LC connector
E1MG-CWDM80-1550 CWDM SFP optic, 80Km, 1550nm, LC connector
E1MG-CWDM80-1570 CWDM SFP optic, 80Km, 1570nm, LC connector
E1MG-CWDM80-1590 CWDM SFP optic, 80Km, 1590nm, LC connector
E1MG-CWDM80-1610 CWDM SFP optic, 80Km, 1610nm, LC connector