PERKO 1156 - Manual

Reference Line
Drill for #8
Screw
Drill for #8
Screw
DRILL 2-1/8 INCH HOLE
MOUNTING TEMPLATE
1156 Series L.E.D.
Cat. No. 1156 Series L.E.D. Courtesy/Utility Light
The above lights are not designed for navigational use.
MOUNTING INFORMATION
Read all instructions before proceeding.
1). These instructions show the orientation of the light after the proper location has been
determined.
2). 1156 lights are supplied with the proper circuit for operation on a nominal 12 volt sys-
tem.
3). These lights contain no user serviceable components.
4). Draw a 6 inch long reference line through the center of the selected mounting location.
5). Cut out the mounting template to the right.Tape it on the mounting surface such that
the reference line (drawn above) passes through the exact center of the template.
6). Drill two holes through the template as indicated for the #8 mounting screws.
7). Drill a 2-1/8 inch hole to accommodate the body as indicated.
8). Attach supply connections to the light, making sure to wire in accordance with both
A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical
Systems (33CFR 183)* If supplied with two black leads, these lights are not polarity
sensitive; otherwise connect red to positive and black to negative electrical supply.
9). Attach the light to the mounting surface using #8 mounting screws. Align two holes in
the edge of the finishing ring with retaining buttons on the plastic flange and snap into
place.
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapollis, MD 21403 (or your local C.G. office)
11/06
1156INS1
Retaining
Button
Retaining
Button
Reference Line
Drill for #8
Screw
Drill for #8
Screw
DRILL 2-1/8 INCH HOLE
MOUNTING TEMPLATE
1156 Series L.E.D.
Cat. No. 1156 Series L.E.D. Courtesy/Utility Light
The above lights are not designed for navigational use.
MOUNTING INFORMATION
Read all instructions before proceeding.
1). These instructions show the orientation of the light after the proper location has been
determined.
2). 1156 lights are supplied with the proper circuit for operation on a nominal 12 volt sys-
tem.
3). These lights contain no user serviceable components.
4). Draw a 6 inch long reference line through the center of the selected mounting location.
5). Cut out the mounting template to the right.Tape it on the mounting surface such that
the reference line (drawn above) passes through the exact center of the template.
6). Drill two holes through the template as indicated for the #8 mounting screws.
7). Drill a 2-1/8 inch hole to accommodate the body as indicated.
8). Attach supply connections to the light, making sure to wire in accordance with both
A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical
Systems (33CFR 183)* If supplied with two black leads, these lights are not polarity
sensitive; otherwise connect red to positive and black to negative electrical supply.
9). Attach the light to the mounting surface using #8 mounting screws. Align two holes in
the edge of the finishing ring with retaining buttons on the plastic flange and snap into
place.
* The above referenced standards can be obtained from:
(1). American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
11/06
Retaining
Button
Retaining
Button
Perko, Inc.
16490 N.W. 13th Avenue
Miami, FL. 33169-5707
www.perko.com
Perko, Inc.
16490 N.W. 13th Avenue
Miami, FL. 33169-5707
www.perko.com 1156INS1