PERKO 1656 - Manual

Cat. Nos. 1440, 1441, 1445, 1450, 1452, 1455, 1456, 1460, 1461, 1465,
1622 & 1656 Series Reduced Glare All-Round Lights
Cat. Nos. 0390, 1401, 1403, 1404, 1209-99A & 1330-99A
Series All-Round Lights (All Sizes)
The above lights are for use on power driven vessels under 20 meters (65.6 ft.) in length operating
on a nominal 12 volt system. Only the 1401, 1403 & 1404 can also be used on sailboats of the
same length (See Diagram #1). All must be used with a separately mounted base. When properly
installed, these replacement poles will comply with ‘72 COLREGS and the U. S.Inland Rules.
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For information on proper light selection, positioning and configuration, refer to A.B.Y.C.
Standard A-16 (1), the ‘72 COLREGS, and the U.S. Inland Rules (2).
2). The center of the lens of white all-round pole lights must be located at least 1 meter (39.4”)
above the center of the lenses of either the bi-color or the red and green side lights on the
vessel. Be sure to use a light with a sufficiently long pole to meet this requirement.
3). IMPORTANT: “Reduced Glare” globes must be vertical during operation. See Diagram #2 in
order to assure compliance with technical details of the regulation and employ the “Reduced
Glare” feature of the series optical system.
4). To store folding lights (series 1450, 1452, 1455 & 1456) grasp both sections of pole and
push towards center coupling (see Diagram #4). While pushing, rotate either until screw is
positioned in open slot. Gently pull poles apart until they are clear of each other, fold one
pole onto the other with wire passing through slot. NOTE: The wire will remain connected to
both poles and will be damaged if too much pulling force is applied.
5). Relamp only with bulb type as marked on globe or inside fixture.
For light Diagram #1 use replacement bulbs PERKO Cat. No. 0337012DP 12V, 11W.
For light Diagram #2 use replacement bulbs PERKO Cat. No. 0338DP2CLR 12V, 9W.
For light Diagram #3 use replacement bulbs PERKO Cat. No. 0337011DP 12V, 7W.
(1) American Boat & Yacht Council, Inc. (2) U.S. Coast Guard
613 Third Street, Suite 10 Washington D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
PERKO, Inc.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
1440INS1
www.perko.com 12/08
Note: Clear Globes Must Be
Vertical During Operation.
DIAGRAM #1
White
Translucent
All-Round Light
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Dates: 2/04/03 & 4/25/03
Meets ABYC A-16
DIAGRAM #2
REDUCED GLARE DIAGRAM #3 DIAGRAM #4
Cat. Nos. 1440, 1441, 1445, 1450, 1452, 1455, 1456, 1460, 1461, 1465,
1622 & 1656 Series Reduced Glare All-Round Lights
Cat. Nos. 0390, 1401, 1403, 1404, 1209-99A & 1330-99A
Series All-Round Lights (All Sizes)
The above lights are for use on power driven vessels under 20 meters (65.6 ft.) in length operating
on a nominal 12 volt system. Only the 1401, 1403 & 1404 can also be used on sailboats of the
same length (See Diagram #1). All must be used with a separately mounted base. When properly
installed, these replacement poles will comply with ‘72 COLREGS and the U. S.Inland Rules.
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For information on proper light selection, positioning and configuration, refer to A.B.Y.C.
Standard A-16 (1), the ‘72 COLREGS, and the U.S. Inland Rules (2).
2). The center of the lens of white all-round pole lights must be located at least 1 meter (39.4”)
above the center of the lenses of either the bi-color or the red and green side lights on the
vessel. Be sure to use a light with a sufficiently long pole to meet this requirement.
3). IMPORTANT: “Reduced Glare” globes must be vertical during operation. See Diagram #2 in
order to assure compliance with technical details of the regulation and employ the “Reduced
Glare” feature of the series optical system.
4). To store folding lights (series 1450, 1452, 1455 & 1456) grasp both sections of pole and
push towards center coupling (see Diagram #4). While pushing, rotate either until screw is
positioned in open slot. Gently pull poles apart until they are clear of each other, fold one
pole onto the other with wire passing through slot. NOTE: The wire will remain connected to
both poles and will be damaged if too much pulling force is applied.
5). Relamp only with bulb type as marked on globe or inside fixture.
For light Diagram #1 use replacement bulbs PERKO Cat. No. 0337012DP 12V, 11W.
For light Diagram #2 use replacement bulbs PERKO Cat. No. 0338DP2CLR 12V, 9W.
For light Diagram #3 use replacement bulbs PERKO Cat. No. 0337011DP 12V, 7W.
(1) American Boat & Yacht Council, Inc. (2) U.S. Coast Guard
613 Third Street, Suite 10 Washington D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
PERKO, Inc.
16490 N.W. 13th Avenue
Miami, FL 33169-5707
1440INS1
www.perko.com 12/08
Note: Clear Globes Must Be
Vertical During Operation.
DIAGRAM #1
White
Translucent
All-Round Light
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Dates: 2/04/03 & 4/25/03
Meets ABYC A-16
DIAGRAM #2
REDUCED GLARE DIAGRAM #3 DIAGRAM #4