PERKO 0617 - Manual

Fig. 0617 Series L.E.D. Side Lights
Patent Pending
These lights are designed for use on the following:
Stealth I Series:
1nm visibility. For use on power driven vessels
under 12 meters (39.4 ft.) in length operating on a nominal 12 volt system.
Stealth II Series:
2nm visibility. For use on power driven vessels
under 20 meters (65.6 ft.) in length operating on a nominal 12 volt system.
In order to comply with ʻ72 COLREGS and the U.S. Inland Rules, the following must be adhered to:
M OUNTING I NFORMATION
Read all instructions before proceeding.
1). These instructions show the orientation of the lights after the proper mounting location has been
determined. For proper light selection, positioning and configuration, refer to A.Y.B.C. Standard A-16*,
the ʻ72 COLREGS*, and the U.S. Inland Navigation Rules*.
2). For installations on conductive surfaces (such as aluminum boats), a gasket set (Perko Cat. No. 0617000GKT)
is available to insure isolation of the fixture and minimize stray current corrosion. Refer to instructions included
with the gasket set for additional mounting details.
3). These lights are designed to be mounted on vertical surfaces that are parallel to the centerline of the boat.
4). Draw a 6 inch long horizontal reference line through the center of the selected mounting location and
parallel to the centerline of the boat.
5). Cut out the mounting template. Tape it on the mounting surface such that the reference line (drawn
above) is directly underneath the reference line marked on the template, and the arrow on the template
points ahead (not astern).
6). Drill 2 holes for #8 pan head screws. Drill a 5/16 inch hole (or 7/16 inch hole if gasket set is installed) to
accommodate the electric wiring.
7). Identify the light based upon the color sticker on the base to assure the light will be mounted on the
correct side of the boat. See Diagram #1.
8). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C. Standard
E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*. Observe
polarity.
9). These lights use L.E.D.ʼs and therefore are not serviceable. Do not attempt to open the lens.
10). Recheck that the red shows port and green shows starboard.
* The above referenced standards can be obtained from:
1) American Boat and Yacht Council, Inc
2) U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
PERKO, INC.
16490 N.W. 13th Avenue
07/12 Miami, FL. 33169-5707
0617INS1 www.perko.com
USCG APPROVAL
33 CFR 183.810
Visibility: Varies
Tested By: IMANNA Labs.
Date: 4/24/08, 4/16/12
Meets ABYC A-16
TEMPLATE
AHEAD
Drill 5/16” hole
for Electric Wiring
(7/16” hole if gasket
set is installed)
Drill for
#8 Pan Head Screws
R
EFERENCE
L
INE
This is a 1”
circle in order
to scale
internet
printed
templates
Red
Green
Vertical Mounting
Surfaces
Diagram #1
Bow
Stern
Stealth I Series: 1nm
0617000STS,
0617DP0STS
0617000BLK, 0617DP0BLK
0617000WHT, 0617DP0WHT
Stealth II Series: 2nm
0617002STS, 0617DP2STS
0617002BLK, 0617DP2BLK
0617002WHT, 0617DP2WHT
Perko Cat. Nos:
Fig. 0617 Series L.E.D. Side Lights
Patent Pending
These lights are designed for use on the following:
Stealth I Series:
1nm visibility. For use on power driven vessels
under 12 meters (39.4 ft.) in length operating on a nominal 12 volt system.
Stealth II Series:
2nm visibility. For use on power driven vessels
under 20 meters (65.6 ft.) in length operating on a nominal 12 volt system.
In order to comply with ʻ72 COLREGS and the U.S. Inland Rules, the following must be adhered to:
M OUNTING I NFORMATION
Read all instructions before proceeding.
1). These instructions show the orientation of the lights after the proper mounting location has been
determined. For proper light selection, positioning and configuration, refer to A.Y.B.C. Standard A-16*,
the ʻ72 COLREGS*, and the U.S. Inland Navigation Rules*.
2). For installations on conductive surfaces (such as aluminum boats), a gasket set (Perko Cat. No. 0617000GKT)
is available to insure isolation of the fixture and minimize stray current corrosion. Refer to instructions included
with the gasket set for additional mounting details.
3). These lights are designed to be mounted on vertical surfaces that are parallel to the centerline of the boat.
4). Draw a 6 inch long horizontal reference line through the center of the selected mounting location and
parallel to the centerline of the boat.
5). Cut out the mounting template. Tape it on the mounting surface such that the reference line (drawn
above) is directly underneath the reference line marked on the template, and the arrow on the template
points ahead (not astern).
6). Drill 2 holes for #8 pan head screws. Drill a 5/16 inch hole (or 7/16 inch hole if gasket set is installed) to
accommodate the electric wiring.
7). Identify the light based upon the color sticker on the base to assure the light will be mounted on the
correct side of the boat. See Diagram #1.
8). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C. Standard
E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*. Observe
polarity.
9). These lights use L.E.D.ʼs and therefore are not serviceable. Do not attempt to open the lens.
10). Recheck that the red shows port and green shows starboard.
* The above referenced standards can be obtained from:
1) American Boat and Yacht Council, Inc
2) U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
PERKO, INC.
16490 N.W. 13th Avenue
07/12 Miami, FL. 33169-5707
0617INS1 www.perko.com
USCG APPROVAL
33 CFR 183.810
Visibility: Varies
Tested By: IMANNA Labs.
Date: 4/24/08, 4/16/12
Meets ABYC A-16
TEMPLATE
AHEAD
Drill 5/16” hole
for Electric Wiring
(7/16” hole if gasket
set is installed)
Drill for
#8 Pan Head Screws
R
EFERENCE
L
INE
This is a 1”
circle in order
to scale
internet
printed
templates
Red
Green
Vertical Mounting
Surfaces
Diagram #1
Bow
Stern
Stealth I Series: 1nm
0617000STS,
0617DP0STS
0617000BLK, 0617DP0BLK
0617000WHT, 0617DP0WHT
Stealth II Series: 2nm
0617002STS, 0617DP2STS
0617002BLK, 0617DP2BLK
0617002WHT, 0617DP2WHT
Perko Cat. Nos: