PERKO 1608 - Manual

Cat Nos.
1608DP0CHR
1608000CHR
1608DP1CHR
1608001CHR
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 02/28/12
Meets ABYC A-16
Cat. No. 1608 Series
L.E.D. Reduced Glare White All-Round Lights
Patent Pending
The above lights are designed for use on power driven vessels under 20 meters
(65.6 ft.) in length operating on a nominal 12 volt system. In order to comply with
ʻ72 COLREGS and the U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16 (1), the ʻ72
COLREGS, and the U.S. Inland Rules (2).
2). These lights are designed to be mounted on a horizontal surface.
3). Horizontal rotation of these lights is unimportant, as all-round lights have 360° horizontal arc of
visibility. However, aesthetically, mount the light as shown in Diagram #1.
4). Cut out the template below. Tape it to the mounting surface.
5). Drill two holes through the template to accommodate #8 oval head mounting screws. Drill one 3/8 inch
hole to accommodate the electrical supply wires.
6). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C. Standard
E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*. Observe
polarity
.
7). Mount the base in accordance with the template.
8). Make sure the light is vertical during operation, in order to assure compliance with the
technical details of the regulations and employ the “Reduced Glare” feature of this optical system. See
Diagram #2
9). These lights use white L.E.D.ʼs and therefore are not serviceable. The lens/globe is permanently
sealed and cannot be opened.
*The above referenced standards can be obtained from:
(1)
American Boat & Yacht Council, Inc. (2) U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
1608INS1
02/12
PERKO, INC.
16490 N.W. 13th Avenue
Miami,FL 33169-5707
www.perko.com
DIAGRAM #1
DIAGRAM #2
Mounting Template
Cat Nos.
1608DP0CHR
1608000CHR
1608DP1CHR
1608001CHR
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 02/28/12
Meets ABYC A-16
Cat. No. 1608 Series
L.E.D. Reduced Glare White All-Round Lights
Patent Pending
The above lights are designed for use on power driven vessels under 20 meters
(65.6 ft.) in length operating on a nominal 12 volt system. In order to comply with
ʻ72 COLREGS and the U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16 (1), the ʻ72
COLREGS, and the U.S. Inland Rules (2).
2). These lights are designed to be mounted on a horizontal surface.
3). Horizontal rotation of these lights is unimportant, as all-round lights have 360° horizontal arc of
visibility. However, aesthetically, mount the light as shown in Diagram #1.
4). Cut out the template below. Tape it to the mounting surface.
5). Drill two holes through the template to accommodate #8 oval head mounting screws. Drill one 3/8 inch
hole to accommodate the electrical supply wires.
6). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C. Standard
E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*. Observe
polarity
.
7). Mount the base in accordance with the template.
8). Make sure the light is vertical during operation, in order to assure compliance with the
technical details of the regulations and employ the “Reduced Glare” feature of this optical system. See
Diagram #2
9). These lights use white L.E.D.ʼs and therefore are not serviceable. The lens/globe is permanently
sealed and cannot be opened.
*The above referenced standards can be obtained from:
(1)
American Boat & Yacht Council, Inc. (2) U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
1608INS1
02/12
PERKO, INC.
16490 N.W. 13th Avenue
Miami,FL 33169-5707
www.perko.com
DIAGRAM #1
DIAGRAM #2
Mounting Template
This is a 3/4”
dia. circle in
order to scale
internet printed
templates
This is a 3/4”
dia. circle in
order to scale
internet printed
templates