PERKO 1604 - Manual

Cat. No. 1604 Series
White All-Round Lights
The above lights are designed for use on power driven vessels under 20 meters (65.6 ft.)
in length operating on a nominal 12 volt system. In order to comply with ‘72 COLREGS and the
U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16*,
the ‘72 COLREGS*, and the U.S. Inland Rules*.These lights are supplied with 12 volt bulbs,
(Cat. No. 0338DP2CLR - 12V, 9W)
2). These lights are designed to be mounted on a horizontal surface. Horizontal rotation of
these lights is unimportant, as all-round lights have 360° horizontal arc of visibility
3). Cut out the template below. Tape it to the mounting surface.
4). Drill two holes through the template to accommodate #8 oval head mounting screws. Drill
one 3/8 inch hole to accommodate the electrical supply wires.
5). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C.
Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR
183)*.
6). Mount the base in accordance with the template.
7). Make sure the light is vertical during operation, in order to assure compliance with the
technical details of the regulations and employ the “Reduced Glare” feature of this optical
system.
*The above referenced standards can be obtained from:
(1).
American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
12/08
MOUNTING Template
Cat Nos.
1604DP0CHR
1604000CHR
PERKO, INC.
16490 N.W. 13th Avenue
Miami,FL 33169-5707
www.perko.com
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 4/25/03
Meets ABYC A-16
Cat. No. 1604 Series
White All-Round Lights
The above lights are designed for use on power driven vessels under 20 meters (65.6 ft.)
in length operating on a nominal 12 volt system. In order to comply with ‘72 COLREGS and the
U.S. Inland Rules, the following must be adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding.
1). For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16*,
the ‘72 COLREGS*, and the U.S. Inland Rules*.These lights are supplied with 12 volt bulbs,
(Cat. No. 0338DP2CLR - 12V, 9W)
2). These lights are designed to be mounted on a horizontal surface. Horizontal rotation of
these lights is unimportant, as all-round lights have 360° horizontal arc of visibility
3). Cut out the template below. Tape it to the mounting surface.
4). Drill two holes through the template to accommodate #8 oval head mounting screws. Drill
one 3/8 inch hole to accommodate the electrical supply wires.
5). Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C.
Standard E-9* and U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR
183)*.
6). Mount the base in accordance with the template.
7). Make sure the light is vertical during operation, in order to assure compliance with the
technical details of the regulations and employ the “Reduced Glare” feature of this optical
system.
*The above referenced standards can be obtained from:
(1).
American Boat & Yacht Council, Inc. (2). U.S. Coast Guard
613 Third Street, Suite 10 Washington, D.C. 20593
Annapolis, MD 21403 (or your local C.G. Office)
12/08
MOUNTING Template
Cat Nos.
1604DP0CHR
1604000CHR
PERKO, INC.
16490 N.W. 13th Avenue
Miami,FL 33169-5707
www.perko.com
USCG APPROVAL
33 CFR 183.810
Visibility: 2nm
Tested By: IMANNA Labs.
Date: 4/25/03
Meets ABYC A-16