beautypg.com

Draw-Tite 118573 T-ONE CONNECTOR User Manual

Hg f e d, English

background image

WARNING

Read and follow all warnings and cautions

printed on the tow vehicle’s battery.

All connections must be complete for the

T-Connector to function properly. Test and

verify installation with a test light or trailer

once installed. For initial test, reset vehicle

electrical system by temporarily removing

the key from the ignition.

8. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid

any areas that would pinch, cut or melt the wire.

9. On the Driver’s side, mount the T-Connector

black box using the double-sided tape provided.

Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid

any areas that would cut or pinch the wire.

10. Reinstall taillight assemblies and other items

removed during installation, being careful not

to pinch or cut the wires.

NOTE

Store 4-Flat in trunk area when not in use.

WARNING

Overloading circuit can cause fires.

DO NOTexceed lower of vehicle manufacturer

rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle’s owners manual & instruction

sheet for additional information.

ENGLISH

TOOLS REQUIRED:

10mm Socket & Ratchet or 10mm Wrench,

Trim Panel Remover, Drill (3/32” Drill Bit),

1/4” Socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

1. Open the rear tailgate to access the bolts

that hold the taillights in place

d

. Remove the

taillights on both the driver and passenger side

of the vehicle

e

.

2. Behind the taillights, there will be connection

points matching the ends of the T-Connector

adapter on the back of each of the vehicle

taillight housings. Beginning on the driver’s

side, separate the vehicle’s wiring connectors,

being careful not to break the locking tabs.

Attach both ends of the T-Connector containing

the yellow and brown wires. Be careful not

to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs

in place.

3. On the Driver’s side, route the T-Connector end

with the green wire and the wire with the 4-Flat

connector down through the opening between

the vehicle bumper and body.

4. Route harness containing the green wire

underneath the vehicle up through the opening

between the vehicle bumper and body to the

passenger’s side taillight pocket. Repeat step

2 using the T-Connector ends containing the

green wire.

5. Locate a suitable grounding point on the driver’s

side near the connectors. Drill a 3/32” hole

and secure white wire with eyelet using screw

provided. Do not drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to

drilling to avoid damage to the vehicle and/

or personal injury. Do not drill into any

exposed surfaces.

6. From inside the vehicle, connect the black 12 ga.

wire and the red wire from the T-Connector black

box with the supplied yellow butt connector.

Either route the black wire thru a grommet and

along the exterior frame or follow the existing

wiring along the thresholds into the engine

compartment up to the battery avoiding areas

that may pinch or break the wire

f

.

WARNING

If routing the wire thru a grommet and along

the exterior of the vehicle, be careful to avoid

any hot pipes, heat shields, the fuel tank or any

other points that may pinch or break the wire.

7. Disconnect the vehicle’s negative (-) battery

cable. If not removed, remove the fuse from the

yellow fuse holder (provided). After cutting the

fuse holder wire

g

, attach the ring terminal

and secure to the vehicle’s Positive (+) battery

cable

h

. Connect the other end of the fuse

holder to the black 12 ga. wire, using the

yellow butt connector (provided).

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et

les instructions avant de commencer l’installation.

Durant l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

118573-037

Rev. A

11/6/2012

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Impreza Sport

h

g

f

e

d