beautypg.com

Draw-Tite 118518 T-ONE CONNECTOR User Manual

Draw-Tite For the car

background image

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.
LISEz CECI En PREmIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.
LEA ESTO PRImERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

118518-037

Rev. A

11/16/10

Installation Instructions

Directives de montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Outlander

ENGLISH

TOOLS REQUIRED:

10mm Socket & Ratchet or 10mm Wrench,

Trim Panel Remover, Drill (3/32” Drill Bit),

1/4” socket, Philips Head Screwdriver, Test-probe

1. Open rear tailgate and locate the vehicle jack storage

compartment on the passenger’s side. Remove panel

and tire jack to access harness area. d e f

nOTE

Set aside all items removed being careful not to

damage parts.

2. Reach inside the jack storage compartment. Locate

the access tray in the wheel well area and gently push

up on the wheel well access tray to remove. Remove

tray and set aside. f The harness is located inside

the access panel area. g

3. Check to see that the mating surfaces of the vehicle

harness connectors match the 10-Pin tow plug

adapter ends. Plug towing harness into white tow

plug. Ensure that the connectors are fully inserted

with locking tabs in place.

4. Locate a suitable grounding point near the connector.

Option 1:

Clean dirt and rustproofing from the area. Drill a 3/32”

hole and secure the white wire using the eyelet and

screw provided. (Do not drill into vehicle floor or bed.

Do not drill into any exposed surfaces.)

Option 2:

Locate existing ground stud. Loosen bolt, place screw

eyelet on stud and re-tighten bolt.

CAUTIOn

Verify what is behind any surface prior to drilling to

avoid damage to the vehicle and/or personal injury.

Do not drill into any exposed surfaces.

5. Locate the T-Connector’s Grey 12-Pin connector and

insert it into the mating connector located on the black

box-module. Check to see that the mating surfaces of

the wiring connectors match. All connector surfaces

should be clean and free of dirt. Be careful not to

damage the locking tabs and be sure that connectors

are fully inserted with locking tabs in place.

6. Locate a flat surface in an out of the way place

and mount the T-Connector’s black box-module,

to prevent damage or rattling.

nOTE

This surface should be in an area that is free of

any moisture and mounted in an area that it is high

enough where it could not be exposed to direct

contact with any water or liquid substance.

WARnInG

The black box-module is intended to be mounted

ONLY in the INTERIOR of the vehicle. Mounting on

the exterior or areas exposed to the elements or

moisture could cause serious damage to the vehicle

and module. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid any

areas that would pinch, cut or melt the wire.

7. Route 4-Flat over to jack storage area.

nOTE

Store 4-Flat in jack storage compartment when

not is use.

BATTERy HARnESS InSTALLATIOn:
8. WARnInG

Read and follow all warnings and cautions printed

on the tow vehicle’s battery. Open the hood and

locate the vehicle’s battery. Using a 10mm Wrench,

disconnect the vehicle’s Negative (-) and Positive (+)

battery cables. h

9. Using a 10mm Socket and Ratchet, temporarily

remove the battery hold down bracket. Carefully move

the vehicle battery enough to gain access behind the

headlamp assembly. h

10. Locate the grey 4-Pin connector taped to a harness

behind the vehicle’s headlamp. Remove the vehicle’s

grey battery harness protective cap and check to see

if the mating surface is clean and free of dirt, clean if

necessary. On the T-Connector’s Battery Harness, if

not removed, remove the fuse from the fuse holder

(provided). Plug Battery Harness into the mating plug.
i j k. Ensure that the connectors are fully inserted

with locking tabs in place.

11. Route wire to the positive battery post. Secure with

cable ties (provided). Carefully replace the vehicle’s

battery back into its original position and re-install

the battery hold down bracket. Attach the fuse holder

(with fuse removed) to the positive (+) terminal of

the battery. Reconnect the vehicle’s Negative (-) and

Positive battery cables and install the 15 amp fuse

into the fuse holder from step 10.

12. WARnInG

All connections must be complete for the T-Connector

to function properly. Test and verify installation with a

test light or trailer once installed. For initial test, reset

vehicle electrical system by temporarily removing the

key from the ignition.

Re-insert key and turn key to the proper position.

13. Reinstall jack storage door, access tray, and other

items removed during installation, being careful not

to pinch or cut the wires.

WARnInG

Overloading circuit can cause fires. DO NOT exceed

lower of vehicle manufacturer rating or:

• Max. stop/turn light: 2 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual & instruction sheet for

additional information.

i

d

f

g

h

e

j

k