beautypg.com

Draw-Tite 118557 T-ONE CONNECTOR User Manual

Hf d

background image

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, Drill (3/32” Drill Bit),

Philips Head Screwdriver, Test-probe

1. Open trunk. Temporarily remove the rear threshold

plate. Partially remove the felt trunk liner behind

the taillights d.

2. On the driver and passenger sides of the

vehicle, locate the vehicle’s taillight wiring

harness. The taillight wiring harness will have

a connection point, on both sides, matching the

ends of the T-Connector. Separate this connector,

being careful not to break the locking tabs.

All connector surfaces should be clean and

free of dirt e.

3. On the driver’s side, insert the T-Connector

end, with the

yellow wire, between the vehicle

wiring connectors and lock into place. Be careful

not to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs

in place.

4. Route the T-Connector end with green wire to the

passenger ‘s side behind the panels and along the

threshold. Repeat step 3 using the T-Connector

ends containing the green wire.

5. Locate a suitable grounding point near the

connector. Clean dirt and rustproofing from the

area. Drill a 3/32” hole and secure the

white

wire using the eyelet and screw provided e.

CAUTION

Verify what is behind any surface prior to drilling

to avoid damage to the vehicle and/or personal

injury. Do not drill into any exposed surfaces.

6. From inside the vehicle, connect the black 12 ga.

wire and the red wire from the T-Connector black

box with the supplied yellow butt connector. Either

route the black wire thru a grommet and along the

exterior frame or follow the existing wiring along

the thresholds into the engine compartment up to

the battery avoiding areas that may pinch or break

the wire f.

WARNING

If routing the wire thru a grommet and along

the exterior of the vehicle, be careful to avoid any

hot pipes, heat shields, the fuel tank or any other

points that may pinch or break the wire.

7. Disconnect the vehicle's Negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse holder

wire, attach the ring terminal and secure to the

vehicle's Positive (+) battery cable g. Connect the

other end of the fuse holder to the black 12 ga.

wire, using the yellow butt connector (provided) h.

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle's battery.

8. Reconnect the vehicle's Negative (-) battery cable

and install the 10 amp fuse into the fuse holder

from step 8.

WARNING

Overloading circuit can cause fires. DO NOT exceed

lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle's owners manual & instruction sheet

for additional information.

118557-037

Rev. A

12/15/2011

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Hyundai Sonata

h

f

d

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning installation.

Wear safety glasses and use all safety precautions

during installation.
LISEz CECI En PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

g

e