Draw-Tite 118596 T-ONE CONNECTOR User Manual
Draw-Tite For the car

ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
Philips Head Screwdriver, Test-probe
1. Open trunk. Temporarily remove the rear
threshold plate. Partially remove the felt trunk
liner behind the taillights
de
.
2. On the driver and passenger sides of the
vehicle, locate the vehicle's taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching the
ends of the T-Connector. Separate the vehicle's
wiring connectors, being careful not to break
the locking tabs. All connector surfaces should
be clean and free of dirt
f
.
3. On the driver's side, attach both ends of the
T-Connector containing the
yellow, brown
and
red wires. Be careful not to damage the
locking tabs and be sure that connectors are
fully inserted with locking tabs in place.
4. Route the T-Connector end with green wire
to the passenger 's side behind the panels
and along the threshold. Repeat step 2 for
T-Connector end with the
green wire
g
.
5. Locate a suitable grounding point near the
connector. Clean dirt and rustproofing from
the area. Drill a 3/32” hole and secure the
white wire using the eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to drilling
to avoid damage to the vehicle and/or personal
injury. Do not drill into any exposed surfaces.
6. From inside the vehicle, connect the black 12
ga. wire and the
red wire from the T-Connector
black box with the supplied yellow butt
connector. Either route the
black wire thru a
grommet and along the exterior frame or follow
the existing wiring along the thresholds into the
engine compartment up to the battery avoiding
areas that may pinch or break the wire
h
.
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
7. Disconnect the vehicle's Negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire
i
, attach the ring terminal
and secure to the vehicle's Positive (+) battery
cable. Connect the other end of the fuse
holder to the
black 12 ga. wire, using the
yellow butt connector (provided)
j
.
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle's battery.
8. Reconnect the vehicle's Negative (-) battery
cable and install the 10 amp fuse into the fuse
holder from step 7.
WARNING
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed. For initial test, reset vehicle
electrical system by temporarily removing
the key from the ignition.
9. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
10. Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
11. Replace carpet, and any other clips or panels
that were removed during installation being
careful not to cut or pinch the wires.
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
118596-037
Rev. A
6/16/2013
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Honda Accord
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
h
e
d
i
j
f
g