Draw-Tite 24907 SPORTFRAME HITCH User Manual
Installation instructions, Nissan sentra, Part numbers

Installation Instructions
Nissan Sentra
(WILL NOT FIT SR MODEL)
Part Numbers:
60338
24907
77294
Hitch Shown In Proper Position
Equipment Required: Power Drill
Wrenches: 9/16 , 11/16
Drill Bits: 1” , 7/16
1.
Hold hitch in place and use as a template to mark holes needed to be drilled in the driver side frame rail. (Hitch can be held up by
the tow hook mount and the 3/8” bolts if needed). Remove hitch after holes are marked in there correct locations.
2.
Fish wire bolts and square hole washers up thru the middle access hole in the frame and out the 2 attachment holes.
3.
Raise hitch into position over the bolts in the frame and attach the 7/16” conical and nut. 3/8” bolts will push through the passenger
side end panel holes that line up with the hitch at the frame rail. Install the 3/8” conical and nuts using a 9/16” socket and a box end
wrench on the end panel side.
4.
Install the 7/16” Carriage Bolt and Block thru the vehicle tow hook and the bracket on hitch. Secure bolt using the 11/16” socket or
box end wrench.
Tighten all 3/8” fasteners with torque wrench to 35 Lb.-Ft.
© 2013 Cequent Performance Products, Inc
Sheet 1 of
24907N
02/07/13
Rev. A
j
Qty. (3)
CARRIAGE BOLT
– 7/16-14 X 1.75 GR5
o
Qty. (1)
BLOCK .250 x 1.00 x 3.00
k
Qty. (3)
CONICAL WASHER
– 7/16”
p
Qty. (2)
LOCKNUT FLG 3/8-16
l
Qty. (3)
HEX NUT
– 7/16-14
q
Qty. (2)
CONICAL WASHER 3/8
m
Qty. (2)
7/16" SQ HOLE WASHER
r
Qty. (2)
PULL WIRE
– 7/16”
n
Qty. (2)
BOLT 3/8-16 X 1.25
Tighten all 7/16” fasteners with torque wrench to 50 Lb.-Ft.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Fastener Kit: 24907F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Wiring Access Location: PC3,4
Form: F205 Rev C 9-17-2012
Accessory Rating
B
k
l
j
m
j
o
p
Figure 4
Fishwiring Location
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Carrying
Ball Mount
2000 (907 Kg)
200 (91 Kg)
n
q
Fascia
Frame
End Panel
Tow hook
Drawbar must be used in the
RISE position only.
Drawbar Kit:
3593
DRILL ACCESS HOLE
IN BOTTOM OF FRAME
FRAME
EXISTING HOLE
EXAMPLE OF FISHWIRE PROCEDURE
KINK FISHWIRE
TO KEEP BLOCK
INDEPENDENT OF BOLT
DRILLED HOLE