beautypg.com

Draw-Tite 24884 SPORTFRAME HITCH User Manual

Installation instructions

background image

Installation Instructions

Hyundai Accent 4 Dr. & 5 Dr.

Kia Rio 4 Dr. Sedan

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required:

Wrenches: 11/16”

5 Door Accent

Tie down hook

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the
Rise position only.

Drawbar Kit:

3592

Fastener Kit: 24884F

24884
60301
77272
24899 UH

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Kink pullwire to keep

spacer independent of bolt

Reverse pullwire technique

4 Door Accent

Frame rail

2

2

2

2

3

3

3

3

3

3

3

3

4

4

4

4

5

5

5

5

6

6

6

6

7

7

7

7

7

7

7

7

7

7

7

7

8

8

8

8

3

3

3

3

4

4

4

4

4 Door Accent/Rio

Item 7

(1) spacer Accent 5 dr

(2) spacers Accent 4 dr

No spacer Rio 4 dr

5 Door Accent

Tie

down

hook

4 Door Accent/Rio
fascia

5 Door Accent
fascia

8

8

8

8

Figure 2.

Figure 3.

Tie down
bracket
on hitch

Tie down bracket
on hitch

1

1

1

1

Hitch bar

Hitch bar

Note: Different configurations due to differences in tie down hooks on each make/model.

Note: Due to different configuration of the vehicles there could be extra spacers, item 7 not used.

1.

Remove rubber plug from frame rails if present. Return to owner on the 5 door and replace after hitch installation on 4 dr models.

2.

On 4 door models using the pullwire method, item 8 (Figure 2), insert items 1 & 2 through forward hole in frame rail as shown.

On 5 door models use the reverse pullwire method (Figure 3) insert items 1 & 2 through hole. Leave pullwires attached.

3.

Insert item 5 carriage bolt through item 6 spacer and then through the tie down hook.

4.

Feed the pullwires through the slot on the hitch bars.

5.

Place item 7 as needed, (1 spacer, 2 spacers, or no spacers), in position on the hitch tie down bracket as shown.

6.

Raise the hitch into position being careful not to push the fasteners into the frame rails. Remove pullwire and attach items 3 & 4

as shown.

7.

Use remaining fasteners to attach to the tie down hook as shown in Figure 1.

8.

Tighten all fasteners to the required torque specification.

©

2012 Cequent Performance Products, Inc.

Sheet 1 of 3

24884N

4-13-12

Rev. A

1

1

1

1

Qty. (2)

Carriage bolt 7/16-14 X 2.00 GR5

5

5

5

5

Qty. (1)

Carriage bolt 7/16-14 X 2.50 GR5

2

2

2

2

Qty. (2)

Spacer .13 X .93 X 3.00, Round corners

6

6

6

6

Qty. (1)

Spacer .25 X 1.00 X 3.00, Square corners

3

3

3

3

Qty. (3)

Conical washer 7/16

7

7

7

7

Qty. (2)

Spacer .25 X 1.50 X 3.00

4

4

4

4

Qty. (3)

Hex nut 7/16-14

8

8

8

8

Qty. (2)

Pullwire 7/16

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form F206 Rev A 5605

Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Example of

pullwire procedure

3

3

3

3

4

4

4

4

4

4

4

4

Note: sort hardware prior to hitch installation to confirm longer 7/16 bolt length for tie down
hook, and small spacers round corners vs. square corners installation

Figure 1.

Figure 3.

on hitch