beautypg.com

Draw-Tite 36486 FRAME HITCH User Manual

Installation instructions, Part numbers

background image

1.

Raise car on ramps, hoist, or jack stands.

2.

Remove 4 rubber exhaust isolators – 2 at the rear of the muffler and 2 near the rear differential. Spray lube helps with removal.

3.

Remove the heat shields by removing 6 nuts per shield with the 10mm wrench.

4.

Remove adhesive cover from over the access hole in frame. With a file open access hole to accept blocks.

5.

Trim heat shields as shown. Approx 7” long and 2-7/8” wide. Trim tip of rubber stand off (shown). Reinstall heat shield.

6.

Install U-bolts over muffler hanger brackets as shown.

7.

Raise hitch into position and install 3/8” hardware finger tight. Checking that the front hole in the bracket lines up with access hole.

8.

Using the hitch as a guide, drill 1/2” hole in car frame.

9.

Remove hitch. Paint bare metal and fish wire bolts and blocks thru access holes. Keep fish wires on bolts to ease hitch installation.

10.

While lifting hitch back into position thread fish wires thru the forward two mounting holes. Finish raising hitch into position and

install the 3/8” washer and nut on the U-bolt.

11.

With carriage bolts thru the mounting bracket remove the fish wires and install the washers and nuts.

12.

Tighten all fasteners.

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Installation Instructions

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: Drill, Tin Snips, file

Wrenches: 10MM, 9/16”, 11/16”

Drill Bits: 1/2”

Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68n*m)

Rev. A

10-7-08

36486N

Sheet 1 of 3

z

2008 Cequent Towing Products

Carriage Bolt – 7/16”-14 x 1.50” long

Qty. (4)

4

Hex nut – 7/16”-14

Qty. (4)

7

Hex nut – 3/8”-16

Qty. (4)

3

Conical Washer – 7/16”

Qty. (4)

6

Conical Washer – 3/8”

Qty. (4)

2

Block – 1 x 2 x 3/16

Qty. (4)

5

U-bolts – 3/8”-16

Qty. (2)

1

Tighten all 3/8 fasteners with torque wrench to 30 Lb.-Ft. (41n*m)

3500 LB (1589 Kg) Max Gross Trailer Weight

300 LB (136 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the
rise position only.

Drawbar Kit:

36065

Fastener Kit: 36486F

Form F206 Rev A 5605

90196

36486

06659

Hyundai Genesis

Frame

Existing Holes

Drilled Hole
Both sides

Muffler
Hanger
Bracket

Heat Shield

Forward

Bumper

1

32

1

32

4

5

67

Rubber
Stand Off

Front Hole

Fish wire (Provided)