Draw-Tite 41929 ULTRA FRAME RECEIVER - Manual

Installation Instructions
DODGE RAM PICKUP
WITH OR WITHOUT O.E.M. HITCH
Part Numbers:
41929
Hitch Shown In Proper Position
Equipment Required: 1500 short bed model – hack saw
Wrenches: 3/4”, 13/16”, 15/16”
Drill Bits: 1/2”
FISHWIRE (SUPPLIED)
Tighten all 9/16-12 fasteners with torque wrench to 110 Lb.-Ft. (149 n*m)
Rev. F 03/12/09 N41929 Sheet 1 of 6 z 2007, 2009 Cequent Towing Products
HEX NUT 1/2” Qty. (6) LOCK WASHER 9/16 Qty. (2) 5
HEX NUT 9/16-12 Qty. (2) 6
LOCK WASHER 1/2” Qty. (6) BLOCK .25 X 1.50 X 2.00 Qty. (2) 4
BLOCK .25 X 2.00 X 2.00 Qty. (2) 9 BLOCK .375 X 1.50 X 3.00 Qty. (2) 3
BLOCK .25 X 1.50 X 3.50 Qty. (2) 8 FLAT WASHER 9/16” Qty. (2) 2
CARRIAGE BOLT 1/2”-13 X 1.75 GR5 Qty. (6) 7 HEX BOLT 9/16-12 X 2.0” GR5 Qty. (2) 1
Tighten all 1/2-13 fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: F41929
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
1200 (545 Kg) 12000 (5448Kg)
Weight Carrying
Ball Mount
1500 (681 Kg) 15000 (6810 Kg) Weight Distributing
Max Tongue
WT (LB)
Max Gross
Trailer WT (LB)
Hitch type
Wiring Access Location: PU3
Form: F205 Rev A 5-6-05
OPTIONAL LOCKING STABILIZING PIN
J-PIN
PART No. 7651 (ORDER SEPARATELY)
BUMPER
O.E.M. RECEIVER
VEHICLE FRAME RAIL SHORT BED
MODEL SHOWN THIS SIDE
HOLES TO BE DRILLED
SHORT BED MODELS ONLY
BOTH HOLES TO BE DRILLED
SHORT BED MODELS ONLY
PUSH/SLIDE 1/4” THICK
BLOCKS THRUOGH END
OF FRAME-BOTH SIDES
SEE FIGURE 2
VEHICLE FRAME RAIL LONG BED
MODEL SHOWN THIS SIDE
FISHWIRE CARRIAGE
BOLTS THROUGH SLOTS
IN FRAME – BOTH SIDES
SEE FIGURE 3
USE THIS HOLE FOR
1500 MODELS
USE THIS HOLE FOR
2500/3500 MODELS
FIGURE 1
PLACE ITEM 3 BETWEEN
BUMPER BRACKET AND
HITCH SIDE BRACKET
AS REQUIRED
11
123456
7 8
11
7
11
9
BUMPER BRACKET
HOLE TO BE DRILLED
LONG BED MODELS
ONLY