Physio-Control LIFEPAK 20e - Manual (Page 215)

Index
LIFEPAK 20e Defibrillator/Monitor Operating Instructions Index-3
©2006-2013 Physio-Control, Inc.
Inde
x
SpO2 volume 3-12
Monitoring the ECG
Adjusting the systole volume 3-3
Motion Detection E-3
N
Noninvasive Pacing 4-3
Indications x
Therapy 4-25
Noninvasive Pacing (see Pacing)
O
ON Control, location of 2-5
Operator’s Checklist D-1
OPTIONS
Control, location of 2-6
How to use 2-16, 8-3
Screen overlay 2-7
Overlay
Alarms 2-18
Channel 1 3-2, 3-3
Manual Mode 4-14
Options 2-7, 2-16
Options/Patient 2-16
Setup passcode 8-3
SpO2 3-12
P
Pace arrow
Internal pacing 1-7
Noninvasive pacing 1-7
PACER Control, location of 2-5
Pacing
Adjust current using CURRENT
Control 2-5
Demand and nondemand 4-25
Noninvasive 4-3
Noninvasive pacing procedure
4-26
Setup menu 8-9
Slow rate using PAUSE control
2-5
Paddle accessory options 5-1
Paper, loading 50mm 2-13
Passcode
Manual Mode 4-14
Set for Setup Mode 8-14
Setup mode 8-2
Patient data, entering
Using OPTIONS 2-7
Patient Reports 6-2
Accessing previous 2-7
Deleting archived patient reports
6-11
Editing archived patient reports
6-10
Managing archived patient
reports 6-7
Transmitting archived patient
reports 6-9
PAUSE Control, location of 2-5
Pediatric paddles 5-1, 5-7
Defibrillation procedure 4-22
Placement 4-21
Removing 5-7, 5-8
Preamble, CODE SUMMARY 6-3
Print configurations before service
or repair 8-2
PRINT Control, location of 2-9
Print Defaults 8-13
Printer
Controls, location of 2-9
Loading 50mm paper 2-13
Setup menu 8-11
Printing
Archived patient reports 6-7
Auto Print Setup menu 8-12
CODE SUMMARY 6-3
Starting 2-9
Stopping 2-9
Pulse Oximeter Sensors 3-13
Q
QRS complex 3-6, 4-26
QRS detection 2-11
Quick Set alarms, setting 2-18
QUIK-COMBO Electrodes 5-3
Connecting to therapy cable 5-4
Electrode placement 3-4, 4-4
Removing electrodes 5-5
Replacing electrodes 5-5
Using when pacing 4-25
R
RATE Control, location of 2-5
Recycling 7-12
Report Types 6-2
Reset Defaults Setup menu 8-13
Resuscitation (see CPR)
R-wave sense marker 1-7
S
Safety
Symbols 1-4
Terms 1-2
SAS
Activate with ANALYZE control
2-5
Electrode contact impedance
E-1
Event 6-6
How SAS operates E-1
Overview E-1
When shock recommended E-1
Screen
Alarms 2-10
Battery charge 2-10
ECG size display 2-10
Messages C-1
Monitoring alarms 2-10
Monitoring parameters 2-10
Selected energy 2-10
Selecting waveform channels
2-12
Status message area 2-10
Time display 2-10
VF/VT Alarm display
Warning messages 2-10
Waveform channel areas 2-10,
2-11, 2-12
Screen Overlay (see Overlay)
Selected energy (screen) 2-10
Send Configuration Setup menu
8-13
Service and Repair 7-12
SERVICE Indicator, location of 2-9
Setup Configuration
Printing before service or repair
8-2
Setup Menus
Advisory Mode 8-7
Alarms 8-11
Auto Print 8-12
Clock 8-12
CPR metronome 8-8
EtCO2 8-10
General 8-4
Manual Mode 8-5
Pacing 8-9
Printer 8-11
Reset Defaults 8-13
Send Config 8-13
Set Passcode (Setup) 8-14
Setup mode passcode 8-14
Setup Options 8-2
SHOCK
Control and Indicator, location of
2-5
Indicator, using the E-3
Shock report 6-6
Short format, CODE SUMMARY
6-5
SIZE
Button 3-3
Control, location of 2-6
Speaker, location of 2-7
SPEED DIAL
Control, location of 2-7
Using the 2-8, 3-2, 3-3, 3-12,
4-26
SpO2
Adjusting pulse tone volume
3-12
Cable connector 2-7
Contraindications
x
How a pulse oximeter works
3-10
Indications x
Monitoring x , 3-9
Monitoring area on screen 2-12
Monitoring considerations 3-11