Extron Electronics IPL 250 Reference Manual - Manual (Page 68)

SIS ™ Programming and Control, cont’d
IPL 250 • SIS Programming and Control 4-12
Command/r
esponse table for SIS commands (continued)
Command
ASCII (T
elnet)
(host to IPL)
URL Encoded (W
eb)
(host to IPL)
Response (IPL to host)
Additional description
Contact closur
e input port
V
iew contact input port state
X!
]
X!
%5D
X4@
]
X4@
= Contact input setting:
0 = of
f/open, 1 = on/closed
Relay port use
Pulse r
elay
X!
*3*
X6#
O
X!
%2A
3
%2A
X6#
O
Cpn
X!
•
Rly
X%
]
X!
= Relay port number
:
01 = Relay port 1,
02 = Relay port 2, 03 = Relay port 3, 04 = Relay port 4 X6#
= Pulse time in 20 ms incr
ements. If
this parameter is missing or = 0, then pulse length = default = 25 = 500
ms.
1
=
20
ms (minimum pulse time) to 65535 =
1310700
ms (maximum pulse time).
Turn r
elay of
f (open)
X!
*2O
X!
%2A
2O
Cpn
X!
•
Rly
X%
]
Turn r
elay on (close)
X!
*1O
X!
%2A
1O
Cpn
X!
•
Rly
1
]
Toggle r
elay
X!
*0O
X!
%2A
0O
Cpn
X!
•
Rly
0
]
V
iew r
elay state
X!
O
X!
O
X%
]
X%
= On/of
f status: 0 = of
f, 1 = on
Firmwar
e version, part number and information r
equests
N
In a query r
esponse, an asterisk (
*) after the version number indicates the version that is curr
ently used.
A
question mark (
? or
?.??
) indicates that the factory default firmwar
e is the only firmwar
e loaded in the IPL
250.
A
carat (
^
) indicates the version of firmwar
e that should be running, but, since a mode 1 r
eset was performed, the factory default firmwar
e version is loaded and running instead.
An exclamation point (
!) indicates that the firmwar
e is corrupted.
N
Responses to commands differ depending on which, if any
, verbose r
esponse mode the IPL
is in.
See the CV command (
E
X2@
C
V
}
) under IP setup commands later in this table.
Query firmwar
e version number
Q
or
1Q
Q
or
1Q
X1!
]
or
V
er01*
X1!
]
Show the IPL
’s firmwar
e version (
X1!
)
to two decimal places. This query yields the number of the curr
ently r
unning version of
the user
-updatable firmwar
e
Example:
1Q
1Q
1.01 or
V
er01*1.01
Query verbose firmwar
e version information
0Q
0Q
{r
esponse fr
om 2Q}–{r
esponse fr
om 3Q}–{r
esponse fr
om 4Q}
]
or
V
er00*{
response fr
om 2Q}–{r
esponse fr
om 3Q}–{r
esponse fr
om 4Q}
]
Show the bootstrap, factory-installed, and updated firmwar
e versions.
See 2Q, 3Q, and 4Q below
.
Example:
0Q
0Q
2.20-1.14(1.77-IPL
Series -W
ed, 16 Jan 2003 00:00:00 GMT)-1.14*(1.77-IPL
Series -T
ue, 16 Jun 2009 16:51:43 GMT)
]
Query firmwar
e version
1Q
1Q
X1!
]
or
V
er01*
X1!
]
This command shows the curr
ently-r
unning
firmwar
e.