Installation instructions (continued), Performance testing, Precision filter cleaning & oiling – S&B Filters Cold Air Intake Kit - Cotton Filter 75-5016 User Manual
Page 3: Related items for your purchase
EMISSIONS STANDARD
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog
check inspection when a Performance Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit
after installation so that a smog check technician can easily verify the E.O. number. As of April 2009, S&B has never had a product
where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check the
status of the exemption process by looking up a specific part number at
The CARB Exemption number and/or
status is listed under the Product Details section for each part number. If the status shows as “Pending,” CARB has yet to issue an
exemption. Products that have not been issued an EO number are street legal in most states, but may not be used on emission
controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer,
log onto our web site and register to receive your Exemption Sticker.
787 S. Wanamaker, Ontario, CA 91761 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -
INSTALLATION INSTRUCTIONS (Continued)
PERFORMANCE TESTING
• Engage parking brake and start your engine.
Listen for abnormal noises. If an air leak is
detected, re-inspect hoses and connections as
they may need to be repositioned and
tightened.
• S&B FILTERS recommends that you keep
your OE intake system in the event it is
required in the future.
• In order to maintain your warranty, all
connections and components must be
checked periodically for alignment and for
proper tension on all connections. Failure to
do so may void your warranty.
• Use only S&B FILTERS cleaning and oil
products to service your filter. Using any other
brand oil and or cleaners on your S&B air filter
may void your warranty.
SEE EXPLODED VIEW ON PAGE 4
PRECISION
FILTER CLEANING & OILING
Part No. 88-0005
Order online today at
through your local S&B distributor.
3
P/N: 75-5016 / 75-5016D
22.
Reconnect the MAF sensor electrical
connection.
21.
With #60 hose clamp
(D)
in place,
install the Intake Tube
(C)
and adapter over
the throttle body. Install the opposite end of
the intake tube into Hump Adapter
(H)
.
Tighten all clamps, starting with the throttle
body.
25.
Remove the protective covering from the
Clear Lid
(R)
and install it on the Air Box
(O)
.
Secure using the 10/24 screws
(S)
and
Sealing Washers
(U)
. Do not over tighten.
23.
Install the Crank Case Vent Hose
(A)
at
the valve cover and Intake Tube
(C)
on the
Passengerʼs side. Secure both ends using
the #8 hose clamps
(B)
.
24.
IF EQUIPPED: Attach the OE brake
boost vacuum line to the Intake Tube
(C)
on
the Driverʼs side and secure using a #8 hose
clamp
(B)
. Caution: Intake Tube
(C)
must be
modified if equipped with vacuum line. See
step #4
26.
Reconnect the battery. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker near the intake kit. The
installation is now complete.
RELATED ITEMS FOR YOUR
PURCHASE
• Replacement Air Filter (Oiled)
(S&B P/N: KF-1049)
• Replacement Air Filter (Dry)
(S&B P/N: KF-1049D)
• Air Filter Wrap (S&B P/N: WF-1016)