Installation instructions (continued), Testing and maintenance, Related items to your purchase – S&B Filters Cold Air Intake Kit - Cotton Filter 75-5064 User Manual
Page 3: Air box end cap testing, Precision ii filter cleaning & oiling
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 -
Installation Instructions (continued)
25.
Reconnect the battery. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker (if applicable) near the
intake kit. The installation is now complete.
Testing and Maintenance
• Engage parking brake and start your engine. Listen for abnormal noises. If an air leak is detected, re-
inspect hoses and connections as they may need to be repositioned and tightened.
• S&B FILTERS recommends that you keep your OE intake system in the event it is required in the future.
• In order to maintain your warranty, all connections and components must be checked periodically for
alignment and for proper tension on all connections. Failure to do so may void your warranty.
• Use only S&B FILTERS cleaning and oil products to service your filter. Using any other brand oil and or
cleaners on your S&B air filter may void your warranty. See
for complete warranty
information.
SEE EXPLODED VIEW ON PAGE 4
3
P/N: 75-5064 / 75-5064D
Related Items to Your
Purchase
• Replacement Air Filter (Oiled)
(S&B P/N: KF-1056)
• Replacement Air Filter (Dry)
(S&B P/N: KF-1056D)
• Air Filter Wrap (S&B P/N: WF-1034)
• Air Scoop
(S&B P/N: AS-1006)
Air Box End Cap Testing
Stock air boxes are a significant contributor to poor air flow which is why S&B designs custom air boxes with secondary and/or enlarged openings. With
that said, S&B recognizes the benefits of cooler air, so we have included a plug to seal off the opening if so desired. For optimal performance, we
recommend that the intake be used without the end cap except in conditions of extreme heat.
ISO 5011 Test Data:
With the plug installed, the intake improves airflow by an average of
30.0%
versus stock.
Without the plug installed, the improvement increases to an average of
36.5%
.
Precision II
Filter Cleaning & Oiling
through your local S&B distributor.
Part #: 88-0008
Emissions Standard
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog check inspection when a Performance
Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit after installation so that a smog check technician can easily verify the E.O. number.
As of April 2009, S&B has never had a product where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check
the status of the exemption process by looking up a specific part number at
The CARB Exemption number and/or status is listed under the Product Details
section for each part number. If the status shows as “Pending,” CARB has yet to issue an exemption. Products that have not been issued an EO number are street legal in most
states, but may not be used on emission controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer, log onto our web site and register to
receive your Exemption Sticker.
22.
Secure the Silicone Step Coupler
(B)
to
the throttle body using a #56 Hose Clamp
(A)
.
Place the #60 Hose Clamp
(C)
around the top
of the Silicone coupler.
23.
Insert the Intake tube assembly into the
Silicone Coupler, then slide the Hump Adapter
over the Adapter Tube. Tighten all hose
clamps when you are satisfied with the
positioning.
24.
Reconnect the Temp. Sensor wiring
harness.
21.
Place a #72 Hose clamp
(F)
over each
end of the Hump Coupler
(G)
. Then slide the
hump coupler over the end of the Intake Tube
(E)
.