Fig.1 – Powersolve HSD10001 Series User Manual
Page 4
Powersolve Electronics Ltd., Unit 8A Arnhem Road, Newbury RG14 5RU, United Kingdom
Tel 0044 (0)1635 521858 Fax 0044 (0)1635 523771
www.powersolve.co.uk
p.4/4 05.12A
(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death)
Terminal Connects:
GND
Input
L1
L2
L3
DC +
Output
DC +
DC -
DC -
Control & monitoring connections:
A= parallel/series mode switcher
B= DC-OK Relay
C= Remote On/Off (shutdown)
Screw terminal order codes:
DC-fail-relay& Shutdown, one plug for each required
(each package = 10 pcs )
Art.No.: 3520037 (2 pins)
Optional Coating (option C):
We offer the HSD-Series with optional coating. It is to be used in e.g. dusty, dirty, high humidity, or in awaiting quick
temperature changes. Short circuit and corrosion at print board lines and at solder points can be prevented. The coat itself is a
transparent acrylic resin. It is procured with a robotics varnishing machine.
Peters SL 1306 N-FLZ (transparent) IEC60216-1 2001, IPC-CC-830B, UL listed as permanent coating FileNo.: E80315 , UL94V-0
Order Codes:
HSD10001.12T 10..17Vdc DIN-Rail
HSD10001.24T 22..30Vdc DIN-Rail
HSD10001.36T 32..43Vdc DIN-Rail
HSD10001.48T 43..53Vdc DIN-Rail
HSD10001.60T 53..72Vdc DIN-Rail
HSD10001.72T 68..86Vdc DIN-Rail
Options to be added to the order-code:
C=coating exs: HSD10001.24TC DIN-Rail+Coating
Backplate-kit (wall-mount):
220.1002.001CA (including Screws)
Mechanics & Installation of the HSD10001:
Stable metal/aluminium housing IP20. To allow adequate convection, a free air space of 50mm (top/bottom) and 5mm (sidewalls) is
required for the HSD10001; for active devices 15mm space from the HSD-sidewalls. For free air convection it is necessary to install the
HSD horizontal (Figure1). You can use the DIN-Rail installation (equiped standard) with our patented 35mm DIN-Rail bracket according
to EN60275. It is easy to mount/dismount while snaping it onto the 35mm DIN-Rail without any tools necessary.It is a wallmount fastener
available as option, too. Use the wall mount option for baseplate-cooling. Consult our support for further information.
Safety Instructions:
Please read all warnings and advices carefully before installing or operating the HSD. Retain this operation manual always
ready to hand.The HSD must be installed by specialist staff only.
Installation:
1.)
The HSD is designed for systems fulfilling the safety norms of
dangerous voltages/energy and fire prevention
2.)
Installation is restricted to specialists only, make sure that the AC
wire system is free of voltage
3.)
Opening the HSD, making any modifications to it, dismounting any
screws from it, operating the HSD out of specification and/or using it
in appropriate area will unevitably result in loosing manufactureres
guarantee; we decline taking any responsibility for risk of demages
caused to someones health or to any installed system.
4.)
Attention: The HSD has an internal input fuse. It is necessary to
wire an automatic circuit braker to the line. We suggest to use a
10A-type with B-characteristic. It is verboten to operate the HSD
without protective earth wired. It essential to install a line switch
before the HSD.
Warnings
:
Disregard these warnings can cause fire, electic shock, serious
accident and death.
1.
Never operate the HSD without Protective Earth
Conductor
2.
Before connecting the HSD to the AC wire system
make all wires free of voltage and assure accidently
switch on
3.
Allow neat and professionel cabeling
4.
Never open nor try to repair the HSD by yourself.
Inside are dangerous voltages that can cause electric
shock hazard.
5.
Avoid metal pieces or other conductive material to fall
into the HSD
6.
Do not operate the HSD under damp or wet conditions
7.
It is verboten to operate the HSD under Ex
conditions or in Ex-Area
Connectors
(IEC60664-1 , IEC61984)
Wiring
Solid
Flexible
AC-Input &
DC-Outputs
0,5...16mm²
22...6 AWG
0,5...14mm²
22...7AWG
Rated Current
76A (+40°C)
76A (+40°C)
Signal
Outputs (A,B)
0,2...2,5mm²
25...14 AWG
0,2...2,5mm²
25...14 AWG
35mm DIN-Rail (EN60725)
Fig.1