Powersolve HSD10001 Series User Manual
Page 2
Powersolve Electronics Ltd., Unit 8A Arnhem Road, Newbury RG14 5RU, United Kingdom
Tel 0044 (0)1635 521858 Fax 0044 (0)1635 523771
www.powersolve.co.uk
p.2/4 05.12A
(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death)
AC Input
2PH & 3PH 340...575Vac , 47...63Hz , 450…820Vdc (2 phase operation 75% rated load max.)
AC Input Rating
400...500Vac (Input Current 3x 3A)
DC Voltage Adjust
10...17V (12V)
22..30V (24V)
32...43V (36V)
43...53V (48V)
53...72V
(60V)*
68...86V
(72V)*
Voltage Protection
21Vdc
32Vdc
50Vdc
56Vdc
84Vdc
92Vdc
Current 60°C*
50.0A (12Vdc)
40.0A (24Vdc)
28.0A (36Vdc)
21.0A (48Vdc)
17.0A (60Vdc)
14.0A (72Vdc)
DC Current 40°C*
50.0A (12Vdc)
45.0A (24Vdc)
31.0A (36Vdc)
23.0A (48Vdc)
18.0A (60Vdc)
15.0A (72Vdc)
Boost 60s/60°C*
55.0A (12Vdc)
44.0A (24Vdc)
30.8A (36Vdc)
23.1A (48Vdc)
18.7A (60Vdc)
16.3A (72Vdc)
Ripple 20MHz
50mVpp
50 mVpp
80 mVpp
100 mVpp
100 mVpp
150 mVpp
Load regulation.*
0-100% 100-0%
±0.5% (12Vdc)
±0.2% (24Vdc)
±0.2% (36Vdc)
±0.2% (48Vdc)
±0.2% (60Vdc)
±0.2% (72Vdc)
*400Vac input
*Power Good Relay & Shutdown: no protective electrical separation >60Vdc !
Tolerance ( at Ua adjusted)
± 0.5%
Transient Time
<1ms (10-100% , 100-10%)
Minimum Load
0 A
Efficiency
92% typical
Load Protection
1,2x I
rated
, auto recovery
Short Circuit Protection
Yes
Temperature Control
Yes (see right graph)
Hold Up Time
> 12ms (400...500Vac input)
Inrush Current Limiter
< 20Apeak 14,4Aeff (400Vac)
Softstart
50ms typical
Temperature Control:
If the ambient temperature (ta)
≤
40°C the HSD provides I/Boost
continuously and if ta
≤
60°C I
rated
is provided continuously. If ta >60°C
derating continuously lowers Vout 2,5%/Kelvin. If ta >70°C (or thermal
overload occures) the HSD shuts down. It auto-recovers when the
device cools down to approved operation conditions.
Cooling
Natural convection
Ambient Temperature
- 25°C…+70°C
Storage Temperature
- 40°C…+85°C
EMI
EN55022 class B / EN61000-3-2
EMS
EN61000-6-2,3 active PFC
Safety
UL60950 , (IEC)EN60950-1
Safety class 1(A)
VDE0805, VDE0100
Creepage Distance
> 10,5mm
Input / Output
Galvanic insulated 3000Vac
Power Good Relay (galv. Ins.)
≤
48Vdc/500mA ,
≤
30Vac/500mA
Relative Humidity
95% (25°C) non-condensing
Pollution Degree
2 (EN50178)
Climatic Class
3k3 (EN60721)
MTBF IEC61709
500000h (IEC61709)
Dimensions (HxWxD)
131.5x200x124.5mm
Weight
3400g
Connectors (AC & DC)
(see page 4)
AWG22...AWG6 (0,5...16mm²)
IEC60664-1, IEC61984
All parameters are specified at +25°C, 15 minutes run in time if not named otherwise.
Specification:
The HSD10001 DIN Rail power supply series is designed for worldwide electronics applications like machine building, railway,
military and factory automation. Its regulated DC output with ripple/noise lower than 50mVpp and its high efficiency of 92%
makes the HSD robust, economical and reliable. Camtec power supplies are traditionally made with high end low ESR
electrolytic output capacitors withstanding +125°C temperature. Our capacitors are rather designed over for longer lifetime and
longer hold up times. The power-boost of the HSD starts DC-loads and DC-motors reliable. The built in function diagnostics
detects malfunctions. The galvanic insulated DC fail relay and remote on/off provides full control over the power supply unit.
The HSD is short circuit and zero load stability protected. It is protected against high transient and provides very good
interference resistance. Equal types of the HSD10001 can be operated in parallel or in series connection. We use IP20 stabile
aluminum housings with ventilation slots in accordance to the demanding VDE norms.
The design meets EN(IEC)60950-1 and low voltage directive EN55022 Class B.
Block Diagram
1)
Transient Suppressor (VDR)
& Filters, Input Fuses
2)
Rectifier
3)
Electronic Inrush Current Limiter
4)
PFC
5)
Load Capacitor C
6)
Potentiometer (P)
Complex sane filter technology using
varistors, supression diodes and X2
capacitors, apply major transient
resistance to the input filter.
Overload: If <0.9xVout applies to the
outputs, the red LED lights and the
DC-OK-Relay (Re) drops (control
message). The green DC-OK LED is
off.
For further
derating
information
see table
page 3