Duro-Last Duro-Grip Insta-Stik - Manual (Page 3)

Duro-Last: The Proven Performer®
"Duro-Last" and "The World's Best Roof" are registered marks owned by Duro-Last , Inc.
www.duro-last.com 800-248-0280
51
TECHNICAL DATA
APPLICABLE STANDARDS
Underwriters Laboratories, Inc. (UL) -
UL 1897 Standard for Safety for Uplift
Tests for Roof Covering Systems.
Note: INSTA-STIK Professional Roof
Insulation Adhesive meets the
requirements of UL 1897 wind uplift
resistance tests for steel deck
applications. If INSTA-STIK is used in a
UL Class A rated roofing system, the
roofing system will maintain its UL Class
A rating.
APPROVALS
FM GLOBAL (FM)
INSTA-STIK Professional Roof
Insulation Adhesive meets the
requirements of the following FM fire
and wind uplift resistance tests for FM
approved roof deck application:
FLAT (Specific Roof Assembly)
· Class 1-60
· Class 1-90
· Class 1-135 · Class 1-150
· Class 1-165 · Class 1-180
· Class 1-195 · Class 1-210
· Class 1-225 · Class 1-240
· Class 1-270
TAPERED (Specific Roof Assembly)
· Class 1-135 · Class 1-150
· Class 1-165 · Class 1-180
· Class 1-195 · Class 1-240
· Class 1-315
Dade County (Florida)
INSTA-STIK Professional Roof
Insulation Adhesive meets the
requirements of Metropolitan Dade
County, Florida, windstorm and fire
classifications for roof deck applications.
Miami Dade Notice of Acceptance
Number - 02-0726.01, expires
10/10/2007
INSTALLATION
The ideal product temperature at the
time of application should be 75°F
(24°C). The minimum ambient and
surface temperatures must be 33°F
(0.6°C) and rising. INSTA-STIK is
packaged in a single container that
should be stored between 50°F (10°C)
and 75°F (24°C). At these
temperatures, the shelf life is 15 months
from the date of manufacture.
SAFETY
When dispensing INSTA-STIK, the
applicator must wear protective clothing,
work gloves, and protective eyewear.
SURFACE PREPARATION
All surfaces must be free of any ice,
snow, frost, debris, dirt, dust, grease,
oil, diesel fuel and standing water before
INSTA-STIK is applied.
Re-Cover Over Bituminous Asphalt
(BUR)
A licensed INSTA-STIK instructor,
authorized to perform adhesion tests,
must be on site prior to the
commencement of the project to
determine compatibility. Please contact
Duro-Last ES department at least
fourteen (14) days in advance for
further instructions.
STEEL DECK
The upper flange of the steel deck must
be free of any debris, dirt, dust, grease,
oil, diesel fuel, standing water, ice, snow
or frost. On new steel, the residual
shop-oil coatingmust be removed using
Red Devil TSP90 or equivalent,
acetone, naphtha, or comparable
cleaner.
INSULATION
Review the roofing insulation plan. The
roof insulation boards to be attached
must be no larger than 4' × 4' (1.2 m ×
1.2 m). In multiple layers of insulation,
the staggered joint method must be
used to eliminate thermal breaks.
PRODUCT & EQUIPMENT
INSTALLATION
lNSTA-STIK Professional Roof
Insulation Adhesive should be mixed
prior to use by firmly holding the
container on its side and agitating the
contents using a side-to-side motion for
at least 15 seconds. Attach the
dispensing hose swivel end to the
cylinder valve. Tighten the connection
using an open-end wrench being careful
not to over tighten. Verify that the on/off
valve on the dispensing hose is closed.
The handle should be perpendicular to
the valve. Attach the dispensing wand
kit to the brass valve by screwing it in
until it is hand tight. The dispensing
wand kit is recommended for roof decks
with many penetrations or confined
areas.
IMPORTANT: When applying
INSTA-STIK, the insulation boards must
be placed onto the INSTA-STIK beads
within 5 minutes. Walk on the boards to
spread the beads for maximum contact.
Continue to walk on the insulation
boards every 5-7 minutes until the
insulation is firmly attached, usually
15-45 minutes.
Figure 4: Installation using INSTA-STIK™ Complete
HANDLING CHARACTERISTICS
Temperature, Humidity Tack Free Time
40 °F (4 °C),
50% relative humidity
45 min.
75 °F (24 °C),
50% relative humidity
15 min.
120 °F (49 °C),
25% relative humidity
13 min.
INSTA-STIK PROFESSIONAL INSULATION ADHESIVE