Ohaus CD-11 Indicator Manual multi User Manual
Page 16
EN-10
CD-11 Indicator
2.6.3 Load Cell Setup Parameters
Review the specifications of the scale base to be used with the Indicator. Make sure the settings you select in
the indicator are compatible with the scale base. The Capacity (full scale), readability (graduation size) and
calibration point (Span and Linearity) selections are shown in the setup table below.
5 0.001, 0.002, 0.005 0.001, 0.002, 0.005 5 2 & 5
10
0.001, 0.002, 0.005, 0.01
0.002, 0.005, 0.01
5, 10 5 & 10
15
0.001, 0.002, 0.005, 0.01
0.005, 0.01
5, 10, 15 5 & 15
20
0.001, 0.002, 0.005, 0.01, 0.02 0.005, 0.01, 0.02 5, 10, 15, 20 10 & 20
25
0.002, 0.005, 0.01, 0.02 0.005, 0.01, 0.02 5, 10, 15, 20, 25 10 & 25
30
0.002, 0.005, 0.01, 0.02 0.01, 0.02
5, 10, 15, 20, 25, 30 15 & 30
40
0.002, 0.005, 0.01, 0.02 0.01, 0.02
5, 10, 15, 20, 25, 30, 40 20 & 40
50
0.005, 0.01, 0.02, 0.05
0.01, 0.02, 0.05 5, 10, 15, 20, 25, 30, 40, 50 25 & 50
60
0.005, 0.01, 0.02, 0.05
0.02, 0.05
5, 10, 15, 20, 25, 30, 40, 50, 60 30 & 60
75
0.005, 0.01, 0.02, 0.05
0.02, 0.05
5, 10, 15, 20, 25, 30, 40, 50, 60, 75 30 & 75
100 0.005, 0.01, 0.02, 0.05, 0.1 0.02, 0.05, 0.1
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100
50 & 100
120 0.01, 0.02, 0.05, 0.1 0.05, 0.1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120
60 & 120
150 0.01, 0.02, 0.05, 0.1 0.05, 0.1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150 75 & 150
200 0.01, 0.02, 0.05, 0.1, 0.2 0.05, 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200
100 & 200
250 0.02, 0.05, 0.1, 0.2
0.05, 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200,
120 & 250
250
300 0.02, 0.05, 0.1, 0.2
0.1, 0.2
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200,
150 & 300
250, 300
400 0.02, 0.05, 0.1, 0.2 0.1, 0.2 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 200 & 400
250, 300, 400
500
0.05, 0.1, 0.2, 0.5
0.1, 0.2, 0.5 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250 & 500
250, 300, 400, 500
600 0.05, 0.1, 0.2, 0.5
0.2, 0.5
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 300 & 600
250, 300, 400, 500, 600
750 0.05, 0.1, 0.2, 0.5
0.2, 0.5
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 300 & 750
250, 300, 400, 500, 600, 750
1000 0.05, 0.1, 0.2, 0.5, 1 0.2, 0.5, 1
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 500 & 1000
250, 300, 400, 500, 600, 750, 1000
1200 0.1, 0.2, 0.5, 1
0.5, 1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 600 & 1200
250, 300, 400, 500, 600, 750, 1000, 1200
1500 0.1, 0.2, 0.5, 1
0.5, 1 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 750 & 1500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500
2000 0.1, 0.2, 0.5, 1, 2 0.5, 1, 2
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1000 & 2000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000
2500
0.2, 0.5, 1, 2 0.5, 1, 2
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1200 & 2500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500
3000 0.2, 0.5, 1, 2 1, 2
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 1500 & 3000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000
5000 0.5, 1, 2, 5
1, 2, 5
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 2500 & 5000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000
7500 0.5, 1, 2, 5
2, 5
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 3000 & 7500
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 7500
10000
0.5, 1, 2, 5, 10
2, 5, 10
5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 5000 & 10000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 7500, 10000
20000
1, 2, 5, 10, 20
5, 10, 20 5, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 10000 & 20000
250, 300, 400, 500, 600, 750, 1000, 1200, 1500, 2000,
2500, 3000, 5000, 7500, 10000, 20000
Full Scale Graduation Size Graduation Size Span Calibration Point Linearity
Capacity with LFT OFF with LFT On and (CPxxxx) Calibration
(Fxxxxx) (gdxxxx) LFT CAn
Points
( not user
selectable)