American Magnetics 12100PS DC Power Supply (CE-Marked) - Manual (Page 8)

OPERATING MANUAL ILLUSTRATIONS AND TABLES
Release 2.0 (98/06) v
LIST OF ILLUSTRATIONS
Figure 1.3-1 Typical Input Current Characteristics, 85-130Vac Range.......................................................1-4
Figure 1.3-2 Typical Input Current Characteristics, 190-264Vac Range.....................................................1-4
Figure 1.3-3 Dimensional Drawings ............................................................................................................1-6
Figure 2.3-1 Power Supply Front Panel.......................................................................................................2-2
Figure 2.3-2 Power Supply Rear Panel........................................................................................................2-2
Figure 2.3-3 Shipping or Storage Carton Label ...........................................................................................2-3
Figure 2.5-1 AC Input Cover and Strain Relief ...........................................................................................2-6
Figure 2.7-1 Maximum Load Wire Length for 1V Line Drop .....................................................................2-10
Figure 2.7-2 Bus Bar Shield ........................................................................................................................2-11
Figure 2.7-3 Typical Load Connection Hardware .......................................................................................2-11
Figure 2.7-4 Output Voltage Connector ......................................................................................................2-12
Figure 2.7-5 Single Load with Local Sensing (Default) ..............................................................................2-13
Figure 2.7-6 Single Load with Remote Sensing...........................................................................................2-13
Figure 2.7-7 Multiple Loads with Local Sensing.........................................................................................2-14
Figure 2.7-8 Multiple Loads with Remote Sensing......................................................................................2-14
Figure 2.8-1 J10 Sense Connector ...............................................................................................................2-15
Figure 2.8-2 Connecting Remote Sense Lines .............................................................................................2-16
Figure 3.2-1 Operating Modes.....................................................................................................................3-1
Figure 3.5-1 Series Operation of Multiple Supplies ....................................................................................3-6
Figure 3.5-2 Parallel Operation of Multiple Supplies..................................................................................3-7
Figure 3.5-3 Split Supply Operation of Multiple Supplies (Two Positive Voltages)...................................3-8
Figure 3.5-4 Split Supply Operation of Multiple Supplies (Positive-negative Supply) ...............................3-9
Figure 4.2-1 Programming and Monitoring SW1 Switch ............................................................................4-1
Figure 4.2-2 Programming and Monitoring J2 Connector ...........................................................................4-2
Figure 4.3-1 Connecting Programming Sources to J2 Connector ................................................................4-6
Figure 5.2-1 Programming and Monitoring Calibration Locations..............................................................5-2
LIST OF TABLES
Table 1.1-1 Available Voltage and Current Ranges ....................................................................................1-1
Table 1.3-1 Specifications for 7.5V to 60V Models.............................................................................. ......1-2
Table 1.3-2 Specifications for 100V to 600V Models............................................................................. ....1-3
Table 2.2-1 Basic Setup Procedure.............................................................................................. ................2-1
Table 2.5-1 AC Input Voltage Ranges and Frequency ................................................................................2-5
Table 2.5-2 AC Wire Specification .............................................................................................................2-5
Table 2.5-3 AC Input Connector Terminals and Connections .....................................................................2-6
Table 2.7-1 Current Carrying Capacity for Load Wiring.............................................................................2-9
Table 2.8-1 Rear Panel J10 Sense Connector Terminals and Functions......................................................2-15
Table 3.2-1 Shipped Configuration (Local Control Mode) ......................................................................... 3-2
Table 3.4-1 Switch Settings for TTL Shutdown Circuit Logic ....................................................................3-5
Table 3.6-1 Switch Settings for Over Temperature Recovery Options........................................................3-9
Table 3.7-1 User Diagnostics ......................................................................................................................3-11
Table 4.2-1 Rear Panel SW1 Switch Assignments (Factory Defaults Underlined) .....................................4-2
Table 4.2-2 Rear Panel J2 Connector Terminals and Functions ..................................................................4-3
Table 4.3-1 Remote Programming Options .................................................................................................4-4
Table 4.3-2 Power Supply Settings for Different Programming Sources ....................................................4-5
Table 4.4-1 Power Supply Settings for Remote Monitoring of Readback Signals ......................................4-6
Table 4.5-1 Isolated (ISOL) Programming Interface Specifications............................................................4-7
Table 4.5-2 J2 Programming and Monitoring Connections with ISOL Interface ........................................4-7
Table 5.2-1 Current Carrying Capacity for Wiring......................................................................................5-1