Yamaha RX-Z11 - Manual (Page 140)

Using multi-zone configuration
140
En
3
Perform the operations in the selected zone.
For further operations, refer to the following pages:
y
To turn off the desired zone, press OZONE 2, OZONE 3, or
OZONE 4 again.
Remote control operations
1
Press H
ZONE repeatedly to select the zone you
want to control.
“MAIN”, “ZONE 2”, “ZONE 3”, or “ZONE 4” indicator
appears in the display window (4) on the remote control.
2
Press E
POWER to turn on the selected zone.
3
Perform the operations in the selected zone.
For further operations, refer to the following pages:
y
To turn off the desired zone, press DSTANDBY.
■ Selecting the input source Zone 2, Zone 3, or
Zone 4
Rotate the D
INPUT selector on the front panel (or set
the operation mode selector to F
AMP and then press
one of the input selector buttons (3)) to select the input
source of the selected zone.
• Select “TUNER” as the input source to use the TUNER features
in the selected zone. For details about the TUNER operations,
see “FM/AM tuning” on page 68.
• Select “XM” as the input source to use the XM Satellite Radio
features in the selected zone. For details about the XM Satellite
Radio operations, see “XM™ Satellite Radio tuning (U.S.A. and
Canada models only)” on page 74.
• Select “DOCK” as the input source to use the iPod features in
the selected zone. For details about the iPod operations, see
“Using iPod™” on page 78.
• Select “NET/USB” as the input source to use the network/USB
operations features in the selected zone. For details about the
iPod operations, see “Using Network/USB features” on page 80.
• The selected input sources are shared across all zones.
• If you set the recording source other than “SOURCE” (see page 66), the
input source of Zone 2 is fixed to the source you set as the recording
source.
■ Adjusting the volume level of Zone 2, Zone 3, or
Zone 4
Rotate E
VOLUME on the front panel (or press
J
VOLUME +/–) to adjust the volume level of the
selected zone.
y
Press LMUTE on the remote control to mute the sound output to the
selected zone.
When you use the external amplifiers in Zone 2 or Zone 3, JVOLUME +/–
can be used only when “Zone2 Volume”, “Zone3 Volume”, or “Zone4
Volume” is set to “Variable” in “Zone2 Set”, “Zone3 Set”, or “Zone4 Set”
(see page 109).
■ Setting the sleep timer for Zone 2, Zone 3, or
Zone 4
Use this feature to turn off the desired zone to the standby mode
after a contain amount of time.
Set the operation mode selector to F
AMP on the remote
control and then press C
SLEEP repeatedly to set the
amount of time.
Each time you press CSLEEP, the sleep timer setting changes as
shown below.
Descriptions Page
“Selecting the input source Zone 2, Zone 3, or Zone 4” 140
“Adjusting the volume level of Zone 2, Zone 3, or Zone 4” 140
“Adjusting the tonal quality of Zone 2, Zone 3, or Zone 4” 141
Descriptions Page
“Selecting the input source Zone 2, Zone 3, or Zone 4” 140
“Adjusting the volume level of Zone 2, Zone 3, or Zone 4” 140
“Adjusting the tonal quality of Zone 2, Zone 3, or Zone 4” 141
Operate the following operations after activating the Zone 2, Zone 3, or
Zone 4 operation mode.
MAIN
ZONE 2 ZONE 3 ZONE 4
(Zone 2) (Zone 3) (Zone 4)
(Main zone)
Notes
Note
120min. 90min.
60min. 30min. OFF