Roland TD-6 - Manual (Page 141)

141
MIDI Implementation
Appendices
❍ Hold 1 (Controller number 64)
Status 2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* In the rhythm part (ch.10), ignored this message.
❍ Effect 1(Reverb Send Level) (Controller number 91)
Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Reverb send level: 00H - 7FH (0 - 127)
❍ RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm = upper byte of parameter number specified by RPN (MSB)
ll = lower byte of parameter number specified by RPN (LSB)
* In the rhythm part (ch.10), ignored this message.
* The value specified by RPN will not be reset even by messages such as program
change or reset all controllers.
* Regarding the RPN please refer to page 136.
On the GM mode of TD-6, RPN can be used to modify the following parameters.
Regarding the value of each parameter, refer to Data Entry (Controller number 6,
38).
RPN
mm
ll Parameter
00H 00H Pitch Bend Sensitivity
00H 01H Channel Fine Tuning
00H 02H Channel Coarse Tuning
7FH 7FH RPN null
● Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* The sound will change beginning with the next note-on after the program
change is received. Voices which were already sounding before the program
change was received will not be affected.
● Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
vv = Channel pressure: 00H - 7FH (0 - 127)
* When channel pressure is received, the effect selected for channel pressure, in
global parameter control (page 142), is applied.
* In the rhythm part (ch.10), ignored this message.
● Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
mm,ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* In the rhythm part (ch.10), ignored this message.
■ Channel Mode Messages
● All Sounds Off (Controller number 120)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
* When this message is received, all currently-sounding notes on the
corresponding channel will be silenced. However, the status of channel
messages will not change.
● Reset All Controllers (Controller number 121)
Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number:0H - FH (ch.1 - ch.16)
* When this message is received, the following controllers will be set to their reset
values.
Controller Reset value
Pitch Bend Change +/-0 (center)
Channel Key Pressure 0 (off)
Modulation 0 (off)
Expression 127 (max)
Hold 1 0 (off)
RPN unset; previously set data will not change
● All Notes Off (Controller number 123)
Status 2nd byte 3rd byte
BnH 7BH 00H
n = MIDI channel number: 0H - FH (ch.1 - ch.16)
* When All Notes Off is received, all notes on the corresponding channel will be
turned off. However if Hold 1 is ON, the sound will be continued until these are
turned off.
■ System Realtime Message
● Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of
all further messages. While monitoring, if the interval between messages
exceeds about 420 ms, the same processing will be carried out as when All
Sounds Off, All Notes Off and Reset All Controllers are received, and message
interval monitoring will be halted.
■ System Exclusive Message
* Regarding the system exclusive message refer to page 137.
The System Exclusive Messages received by the normal mode of TD-6 are;
Universal Non-realtime System Exclusive Messages, Universal realtime System
Exclusive Messages, Data Requests (RQ1), and Data Set (DT1).