Sharp Digital Laser Copier/Printer AR-5127 - Manual (Page 34)

AR-5127 SIMULATION 8 - 6
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
Note: Executable only when the finisher is installed.
Operation/procedure
After the paper size is set, the side guide plate and the rear guide plate
are set.
Shifts to the specified paper size position.
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
Example: When the side guide plate value is adjusted in A3, the same
adjustment is made in A4. (Value 1 in the table)
Note: Executable only when the finisher is installed.
Operation/procedure
Note: Executable only when the finisher is installed.
8:OGSLR
Transport selection gate solenoid (R)
9:OGSLL
Transport selection gate solenoid (L)
10:JGSL1 Rear edge plate drive solenoid
11:JGSL2
Upper alignment plate drive solenoid
12:SHTSL Shutter drive solenoid
13:T2SCL Paper exit roller clutch
14:STGSL
Paper holding solenoid
3-6
Purpose Adjustment
Function
(Purpose) Used to adjust the finisher jogger position.
Section Sorter/Finisher
Item Operation
(Initial screen) (Input screen) (Executing screen)
Display items Content
Setting
range
Default
1:PAPER SIZE
Paper size
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT,
8:LG, 9:FC, 10:LTR,
11:8K, 12:16K) 1-12
2:JOGGER POS X Side guide plate 1-99 50
3:JOGGER POS Y Rear edge guide plate
Paper size
Side guide plate
adjustment value number
Adjustment value number
of the rear edge guide
plate
A3 1 2
A4 1 9
B4 3 3
B5 3 10
A4R 5 6
WLT 2 1
LT 2 8
LG 4 4
FC 4 5
LTR 4 7
8K 6 11
16K 6 12
Sim3-6 JOGGER ADJ.
1:PAPER SIZE
2:JOGGER POS X
3:JOGGER POS Y
1
Sim3-6 JOGGER ADJ.
2:JOGGER POS X 50
EXEC [ 0- 99] 50
Sim3-6 JOGGER ADJ.
2:JOGGER POS X 50
EXEC [ 0- 99] 50
3-7
Purpose Adjustment
Function
(Purpose) Used to adjust the offset tray operations.
Item Operation
(Initial screen) (Input/Selection screen) (Executing screen)
Display items Content
Installation
range
Default
1:PAPER PUSH TMG Paper holder
descending timing in
non-staple 34-66 50
Used to adjust the descending timing of the
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking.)
2:PAPER OUT DOWN Tray descending
distance after non-
staple paper exit 0-12 1
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
3:STAPLE UP Tray lift distance
before staple paper
exit 0-12 6
The height of the tray standby position in
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
4:STAPLE DOWN Tray descending
distance after staple
paper exit 0-12 6
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
5:OFFSET INI.POS Offset tray shift
position adjustment 0-99 13
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0 - 94 (Shipment position: 13))
1) Initialize the offset tray normally.
2) The tray descends to the parameter posi-
tion + 1 pulse position.
3) The tray lifts up to the specified parame-
ter position.
(Disassembly position: 94 - 99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray, the
tray cannot descend to the specified posi-
tion. Check to insure that there is no paper
in the tray before execution.
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
2:PAPER OUT DOWN 1
3:STAPLE UP 6
1/2
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
[ 34- 66] 50
Sim3-7 OFFSET ADJ.
5:OFFSET INI.POS 13
EXEC [ 0- 99] 13