FUJITSU SCANPARTNER 600C User Manual
Page 4
iv
4.4.3 INQUIRY command ......................................................................................................................................4-22
4.4.3.1 INQUIRY command: COMMAND phase (initiator
→
target) ...................................................................................4-22
4.4.3.2 Inquiry data: DATA IN phase (target
→
initiator) .....................................................................................................4-24
4.4.4 REQUEST SENSE command.........................................................................................................................4-26
4.4.4.1 REQUEST SENSE command: COMMAND phase (initiator
→
→
target) .....................................................................4-26
4.4.4.2 Sense data: DATA EN phase (target
→
initiator) ......................................................................................................4-27
4.4.5 SEND DIAGNOSTIC command ....................................................................................................................4-29
4.4.5.1 SEND DIAGNOSTIC command: COMMAND phase (initiator
→
→
target) .................................................................4-30
4.4.5.2 Contents of self-test..................................................................................................................................................4-31
4.4.5.3 Results of self-test....................................................................................................................................................4-31
4.4.6 TEST UNIT READY command ......................................................................................................................4-31
4.4.6.1 TEST UNIT READY command: COMMAND phase (initiator
→
target) ..................................................................4-32
4.4.6.2 Acknowledgment......................................................................................................................................................4-32
4.4.7 SET WINDOW command ..............................................................................................................................4-33
4.4.7.1 SET WINDOW command: COMMAND phase (initiator
→
target)...........................................................................4-33
4.4.7.2 Window date: DATA OUT phase (initiator
→
target) ...............................................................................................4-34
4.4.7.3 Update of ScanPartner 600C OEM manual ...............................................................................................................4-39
4.4.7.4 B&W Scanning Vender unique parameters ...............................................................................................................4-39
4.4.7.4.1 Vendor unique identification code: Byte 28 .......................................................................................................4-40
4.4.7.4.2 Paper size: byte 35 ............................................................................................................................................4-40
4.4.7.5 Color Scanning Vender unique parameters ...............................................................................................................4-41
4.4.7.5.1 Vendor unique identification code: Byte 28 .......................................................................................................4-41
4.4.7.5.2 Parameter length: Byte 29 .................................................................................................................................4-41
4.4.7.5.3 Color scanning parameters ................................................................................................................................4-41
4.4.8 OBJECT POSITION command......................................................................................................................4-43
4.4.8.1 OBJECT POSITION command: COMMAND phase (initator
→
target) ....................................................................4-44
4.4.8.2 Acknowledgment......................................................................................................................................................4-45
4.4.8.3 ADF sequence ..........................................................................................................................................................4-46
4.4.9 READ command ...........................................................................................................................................4-46
4.4.9.1 READ command: COMMAND phase (initiator
→
target).........................................................................................4-47
4.4.9.2 DATA IN phase (target
→
initiator) .........................................................................................................................4-48
4.4.10 Scan command............................................................................................................................................4-49
4.4.10.1 SCAN Command phase (initiator
→
target) ............................................................................................................4-49
4.5 S
TATUS
: STATUS
PHASE
(
TARGET
→
INITIATOR
)..................................................................................................4-50
4.6 M
ESSAGES
...........................................................................................................................................................4-51
4.6.1 ATN detection...............................................................................................................................................4-51
4.6.2 Message types...............................................................................................................................................4-52
4.6.2.1 COMMAND COMPLETE (X'00'): MESSAGE IN phase (target
→
initiator) ............................................................4-52
4.6.2.2 INITIATOR DETECTED ERROR (X'05'): MESSAGE OUT phase (initiator
→
target).............................................4-52
4.6.2.3 ABORT (X'06'): MESSAGE OUT phase (initiator
→
target).....................................................................................4-53
4.6.2.4 MESSAGE REJECT (X'07'): MESSAGE IN/OUT phase (initiator
→
target) ............................................................4-53
4.6.2.5 NO OPERATION (X'08'): MESSAGE OUT phase (initiator
→
target)......................................................................4-54
4.6.2.6 MESSAGE PARITY ERROR (X'09'): MESSAGE OUT phase (initiator
→
target)....................................................4-54
4.6.2.7 BUS DEVICE RESET (X'0C'): MESSAGE OUT phase (initiator
→
target) ..............................................................4-54
4.6.2.8 IDENDIFY (X'80' TO X'FF'): MESSAGE OUT phase (initiator
→
target).................................................................4-55
4.7 C
OMMAND
S
EQUENCE
..........................................................................................................................................4-56
4.7.1 Initial sequence ............................................................................................................................................4-56
4.7.2 Read sequence ..............................................................................................................................................4-57
4.7.2.1 Read sequence for B&W mode .................................................................................................................................4-57
4.7.3 READ command sequence ............................................................................................................................4-57
4.7.3.1 Single READ ...........................................................................................................................................................4-57
4.7.3.2 Multiple READ........................................................................................................................................................4-58
4.8 S
TATUS
T
RANSITION OF
L
OGICAL
U
NIT
.................................................................................................................4-59
4.9 E
RROR
T
ABLE
......................................................................................................................................................4-60
4.10 I
TEMS FOR
S
PECIFYING
W
INDOW
.........................................................................................................................4-61
5. DIAGNOSTICS.........................................................................................................................................................5-1
5.1 O
NLINE DIAGNOSTICS
.............................................................................................................................................5-1
5.2 O
FFLINE DIAGNOSTICS
............................................................................................................................................5-2
5.3 D
IAGNOSTIC FLOWCHARTS
......................................................................................................................................5-3
5.3.1 Group 1 error flowchart (Lamp assembly).......................................................................................................5-3
5.3.2 Group 2 error flowchart (Flatbed/ADF motor)................................................................................................5-3
5.3.3 Group 3 error flowchart (paper in ADF paper tray) ........................................................................................5-4