Filter identification – Airaid 510-223 User Manual
Page 2
11. A) Install the hump hose (#7) onto the filter
adapter using two #72 hose clamps (#19). B) In-
stall the smaller end of the reducer coupler (#6)
onto the throttle body using one #52 hose clamp
(#17). Next install the #56 hose clamp (#18) over
the coupler and leave it loose. C) Now align the
#110 bracket (#24) over the captured nut in the
fender well and install one 6mm bolt (#16) and
washer (#14). Leave loose until final adjustment.
12. Install the Airaid intake tube into the hump
hose first and then into the coupler on the throttle
body. Adjust for fit, and then tighten all four hose
clamps. Next install the 1/2” breather hose (#22)
between the Airaid intake tube and the valve cov-
er securing it with one Speed clamp (#21) on each
end. Next install the 1/8” vacuum hose (#23) onto
the Airaid intake tube, and connect the other end
to the vacuum connection on the engine. Recon-
nect the wiring harness connector to the MAF
sensor. Refer to step #4.
13. Fasten the #203 bracket (#26) to the existing
hole in the radiator support using one 1/4-20x1/2”
button head bolt (#13) washer (#14), and serrated
nut (#15). Tighten all nuts and bolts that hold the
CAD to the vehicle at this time.
14. Install the Airaid Premium Filter (#1) onto the
filter adapter and tighten the clamp. Next install
the weather strip (#8) on top of the CAD as
shown. For an easier install, start at the fender
side of the CAD and work your way towards the
radiator. Reinstall the factory beauty cover.
15. Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Periodically check
the tightness of all hose clamps. Double check
the hood clearance.
16. Reconnect the negative battery
cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.10.11.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris, care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
10. Install the 1/8” barbed fitting (#20) into the
Airaid intake tube (#2) as shown. Next install the
MAF sensor r emoved in step #9, into the
Airaid intake tube and secure it with two 8/32” x
3/8” (#12) button head screws. Do Not Use The
Factory Screws!
A.
B.
C.
FILTER IDENTIFICATION
720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red
722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.