Filter identification – Airaid 450-234 User Manual
Page 2
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951
8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear
to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts
are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to
drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The
air filter is reusable and should be cleaned periodically.
17. Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses, con-
nectors, bolts, and screws are tight.
Periodically check the tightness of all hose
clamps.
18. Re-connect the negative battery
cable!
10. Insert the Airaid intake tube thru the CAD panel
and then reinstall the Mass Air Flow sensor from step
#5 using the two supplied 8-32x3/8” button head
screws (#15). Do Not Use The Factory Screws!
11. Now turn the intake tube counterclockwise until
the mounting holes align thru the panel. Secure the tube
to the panel using the two 1/4”-20 button head bolts
(#10) and 1/4” washers (#11).
12. Insert the factory elbow removed in step #3 into the
large grommet on the side of the intake tube as shown.
A drop or two of dish soap or something similar will
help make the elbow slide thru the grommet easier.
13. A.) Install the fr ont br acket (#18) onto the fr ont
of the CAD as shown using one 1/4”-20x5/8” hex bolt
(#13), two 1/4” flat washers (#12), and one lock nut
(#14). B.) Next mount the factory scoop to the
bracket as shown using one 1/4”-20x5/8” hex bolt
(#13), two 1/4” flat washers (#12), and one lock nut
14. Install the CAD into the vehicle making sure to slip
the intake tube into the hump hose as you lower the
assembly into place. After you have the intake tube
correctly located into the hump hose, insert the billet
rivet (#19) thru the CAD and into the factory grommet
in the inner fender well. Tighten the hose clamp on the
hump hose and then reinstall the two factory bolts re-
moved in step #1 that secure the scoop to the radiator
support. Reconnect the Mass Air Flow sensor!
15. Install the side bracket (#17) onto the CAD as
shown using the factory bolt removed in step #6, and
one 1/4”-20x5/16 hex bolt (#13), two 1/4” flat washers
(#12), and one lock nut (#14).
A
.
B
.
Billet Rivet
16. A.) Reinstall the small br eather hose into the
grommet on the top of the intake tube. Reconnect the
large breather connector to the factory elbow. B.) Next
mount the Airaid Premium Filter (#1) onto the intake
tube as shown and tighten the clamp. C.) Install the
weatherstrip (#6) onto the top of the CAD panels as
shown. Start at the front of the vehicle and work your
way towards the fender.
A
.
B
.
REV.10.25.13
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search
function to find your part number, and click View Details.
FILTER IDENTIFICATION
720-448 Airaid Oiled Media 721-448 Airaid SynthaMax Dry Media - Red
722-448 Airaid SynthaMax Dry Media - Black 723-448 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.