Filter identification – Airaid 400-246 User Manual
Page 2
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.10.24.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
10. Insert the Airaid Intake Tube into the CAD assem-
bly, then slide the Hump Hose onto the turbo inlet and
tighten the Clamps. Reconnect the filter minder and the
air temp sensor.
11. Secure the Intake Tube to the CAD assembly using
three 1/4-20 Button Head bolts (#14) and 1/4” Flat
Washers (#15). Tighten the factory bolts in the Panel
assembly from step 8.
12. Vehicles equipped with a power distribution box
mounted on the left inner fender, will remove the bolt
from the factory bracket, slide in the bracket 140 (#12)
and replace the factory bolt. If you don’t have the distri-
bution box, install the provided 1/4-20 button head bolt
(#14), washer (#15), and nut (#16), through the inner
fender, and tighten. Now tighten the button head bolt
that holds the L-bracket to the panel.
16. Install The Airaid Premium Filter (#1).
17. Install the CAD Lid (#6) as shown and secure using
four 1/4-20 Button Head Bolts and 1/4” Flat washers.
Complete the Installation by attaching the Weather Strip
(#9) to the CAD assembly edge surrounding the Filter.
18..
Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses, bolts,
and screws are tight. Double check the hood
clearance. Reconnect the battery cables.
13 . Place the second bracket 140 (#12) onto the 6mm
core support stud and secure using the 6mm flanged nut
(#18). Attach the Bracket to the Panel using one 1/4-20
Button Head Bolt, 1/4” Flat Washer, and 1/4-20 Flange
Nut.
14. Place the Battery Mat (#7) into the CAD assembly
with drain tube on the Drivers side.
15. Secure the battery in place using the new 1/4-20 J
Bolts(#11), Tie Down (#8) and 1/4-20 Flange nuts. The
CAD Panels ar e slotted to accommodate the J Bolts.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
FILTER IDENTIFICATION
720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red
722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.