Airaid 400-217 User Manual
Page 2
10. Slip two rubber grommets (#17) into the large
holes in the factory airbox mounting plate, and
then slide them sideways into the small holes as
shown.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.10.23.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
12. Align the hole in the CAD with the hole in the
factory coolant reservoir mount. Insert one M6-
1x25 hex bolt (#18) and 1/4” flat washer (#13)
through the hole in the CAD, through the coolant
reservoir mount, and into the speed nut below it.
13. Insert two ¼ - 20 x 7/8” bolts (#12) and ¼” flat
washers (#13) through the holes in the CAD and
thru the grommets. On the underside of the factory
airbox mounting plate, align the long/narrow
bracket (#19), two ¼” flat washers (#13), and two
¼ - 20 locknuts (#15) with the ¼-20 x 7/8” bolts.
Tighten the assembly securely.
15. Install the reducer coupler (#7) onto the Airaid
Intake Tube (#4) using one #48 hose clamp (#23)
on the small end of the coupler, and one #52 hose
clamp (#24) on the big end. Slide the tube into the
hump hose first, and then over the throttle body.
Adjust for fit, and tighten the clamps. Reconnect
the factory breather hose.
11. Install the CAD assembly into the vehicle. First,
align the filter adapter with the factory MAF sensor
housing, then, secure it with the factory clamp.
18. Double check your work!
Make sure there is no foreign material in
the intake path. Make sure all clamps, hos-
es, bolts, and screws are tight.
19. Reconnect the negative battery
cable!
16. Install the Airaid Premium Filter (#1) onto the
CAD and tighten the clamp. Install the weather
strip (#8) onto the top edge of the CAD as shown.
(Hint: start at one end and work your way around
to the other.)
17. Slip the black plastic hose mount (#20) over
the radiator overflow hose. Next, place one ¼” flat
washer (#13) over the hole on the inner drivers side
fender. Slide the hose mount prongs thru the fender
and thru the washer.
14. Using a 10mm socket, remove one factory bolt
from under the throttle body. Using a 5/32” allen
wrench, install the M6x1x20 button head bolt (#26)
in its place. Install the urethane hump hose (#6) and
two #80 hose clamps (#25) onto the factory MAF
sensor housing. (Leave the clamps loose for now).
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.
FILTER IDENTIFICATION
700-445 Airaid Oiled Media 701-445 Airaid SynthaMax Dry Media - Red
702-445 Airaid SynthaMax Dry Media - Black 703-445 Airaid SynthaMax Dry Media - Blue