Double check your work, Reconnect the negative battery cable – Airaid 400-109 User Manual
Page 2
17. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts,
and screws are tight.
18. Reconnect the negative battery cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.10.18.13
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
10. Install the small side of the urethane reducer
hose (#5) onto the throttle body using one #52
hose clamp (#14). Install one #60 hose clamp
(#13) onto the larger side of the reducer hose.
Tighten only the clamp on the throttle body.
11. Install the 7/16” rubber grommet (#15) into
the Airaid Intake Tube (#2). Insert the factory
AIT sensor into the gr ommet. Slip the Air aid
Intake Tube into the urethane hump and reducer
hoses. Align for best fit and tighten the remain-
ing hose clamps. Tighten the MAF bracket
and
reconnect the AIT sensor wiring harness.
12. Install the 5/8”X18” breather hose (#6) onto the
valve cover breather fitting then onto the Airaid In-
take Tube nipple. Secure the hose using two #19
speed clamps (#16).
16. Install the Airaid Premium Filter (#1) onto the
MAF bracket, and tighten the clamp. Reinstall the
beauty cover using the three factory bolts.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
13. 5.4L engines: Measure and cut the 3/4 x 12”
L-hose (#7) as needed
,
then slide it over the fac-
tory plastic IABV hose. Install the hose onto the
Airaid Intake Tube nipple and secure it using two
#22 speed clamps (#17).
14. 4.6L engines: Rotate the IABV inlet tube 90
degrees to provide clearance for the 3/4 x 12” L-
hose (#7).
Slide the L hose over
the factory plastic
IABV hose.
15. 4.6L engines continued: Connect the Airaid
Intake Tube nipple to the IABV inlet tube using
the 3/4 x 1/2” L-hose (#7), and two #22 speed
clamps (#17).
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
FILTER IDENTIFICATION
700-420 Airaid Oiled Media 701-420 Airaid SynthaMax Dry Media - Red
702-420 Airaid SynthaMax Dry Media - Black 703-420 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.