Airaid 310-205 User Manual
Page 2
19. Double check your work!
Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.
20. Reconnect the negative battery cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.7.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
13. Install the provided hump hose (#7) onto the
air filter adapter. Place a #60 hose clamp (#15) on
each side of the hump hose. Tighten only the
clamp on the air filter adapter. Leave the other
clamp loose for now.
14. Remove the factory intake air temp sensor from
the resonator box by carefully twisting the sensor
body, and pulling it straight out of its mount. Place
the sensor in a safe location, it will be re-used in
step #15.
15. Install the rubber grommet (#12) into the Mod-
ular Intake Tube (#5). Next, slide the factory in-
take air temp sensor into the grommet in the tube.
Make sure it is seated all of the way in.
16. A.) Install the Modular Intake tube into the
hump hose end first. B.) Insert the opposite end of
the Modular Intake tube into the reducer, on the
throttle body. Adjust components for fit, and then
tighten all of the hose clamps, and reconnect the
factory intake air temp sensor wiring harness.
17. Install the Airaid Premium Filter (#1) onto the
air filter adapter. Next, install the weather strip
(#8) on the top of the Quick Fit panels as shown.
18. Reconnect the factory breather hose onto the
90º nylon fitting (#9).
10. Install the 90° nylon fitting (#9), into the air
filter adapter.
11. Install the Quick Fit panels into the factory
lower airbox by lining up the three tabs in the rear
of the panel, the latch holes in the front, and then re
-latching the factory airbox clips. Next, using the
1/4– 20x1/2” button head screws (#10) and 1/4”
flat washers (#11), install the air filter adapter into
the Quick Fit Panel.
12. Install the provided reducer (#3) onto the throt-
tle body with the smaller diameter towards the
throttle body. Place the #48 hose clamp (#6) on
the smaller diameter section of the reducer (throttle
body side). Place the #52 hose clamp (#7) on the
larger diameter side of the reducer. Leave the
clamps loose for now.
B
A
FILTER IDENTIFICATION
700-452 Airaid Oiled Media 701-452 Airaid SynthaMax Dry Media - Red
702-452 Airaid SynthaMax Dry Media - Black 703-452 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.