Airaid 300-209 User Manual
Page 2
16. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and
screws are tight. Periodically check the tightness of all hose clamps.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.5.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST week-
days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA-
TER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
10. Assemble the Cool Air Dam panels as
shown using the seven 6-32x5/16” screws (#8),
#6 flat washers (#9), and keps nuts (#10). Next
install the Airaid filter adapter thru the CAD
panel using three 1/4-20x1/2” button head bolts
(#11), and 1/4” flat washers (#12). (See Arrow)
11. Install the CAD assembly into the vehicle,
and install the 3/8-16x1 1/4” button head bolt
(#18) thru the panel, and into the well nut. Next
install the 6x1x12mm hex bolt (#16), and 1/4”
flat washer (#12), thru the panel, and into the
captured nut in the radiator support. Leave all
bolts loose until final adjustment.
12. Using one 1/4-20x1/2” button head bolt
(#11), 1/4” flat washer (#12), and 1/4” serrated
nut (#13), and the 8x1.25x30mm hex bolt
(#14), and 5/16” flat washer (#15), mount the
supplied bracket (#19) between the CAD panel,
and the fan shroud mounting boss as shown.
Tighten all CAD mounting bolts at this time.
13. A) Slide the r ubber elbow over the
Airaid filter adapter, install one #80 hose clamp
(#20), and tighten the hose clamp. B) Using
three 8-32x1/2” button head screws (#13), rein-
stall the factory Mass Air Flow sensor, and
temperature sensor into the Airaid filter adapt-
er. Do Not Use The Factory Screws! C) Rein-
stall the wiring harness anchor into the hole in
the filter adapter just below the temperature
sensor.
14. Tighten the factory hose clamp where the
Airaid metal tube slips into the factory rubber el-
bow on the turbocharger.
15. Install the Airaid Premium Filter (#1) onto
the Airaid filter adapter, and tighten the hose
clamp. Install the weather strip (#7) onto the
top of the CAD, starting at the fender, and
working your way towards the radiator.
B
C
A
17. Reconnect the negative battery cables!
FILTER IDENTIFICATION
720-128 Airaid Oiled Media 721-128 Airaid SynthaMax Dry Media - Red
722-128 Airaid SynthaMax Dry Media - Black 723-128 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not re-
quire oil. Service air filter as need-
ed by cleaning with common non-
petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.