Airaid 250-255C User Manual
Page 2
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.05.20.14
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
11. Install the Bracket (#28) on to the Rear Panel (#3) as
shown using one 1/4-20 Button Head Screw (#17), 1/4”
Flat Washer (#20), and 1/4” Serrated Nut(#21). Com-
plete the assembly by attaching the Airaid Premium Fil-
ter (#1) to the Filter Adapter (#10).
13. Install the Airaid Intake Tube assembly onto the
filter adapter first, and then onto the throttle body. Ad-
just for fit, and tighten all the hose clamps. Next, recon-
nect the MAF and MAP sensors.
14. A) Replace the factory breather line on the valve
cover with the 26” Airaid Breather Hose(#12). B) Se-
cure the breather hose to the intake tube nipple using the
black Speed Clamp (#32).C) Slide the Edge Clip Cable
Ties (#31) about 6” apart along the fender pinch weld
and return the coolant line to it’s original location. Se-
cure the coolant line using the cable ties and trim off
excess.
Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses, bolts,
and screws are tight. Double check the hood
clearance.
15. A) Install the 11” Weather Strip (#11) onto the
curved edge of the top cover (#6) and install the top cov-
er onto the Airaid filter box using the four 1/4-20 Black
screws.(#22). B) Line up the intake bracket with the
fender bolt hole, and secure the assembly using the fac-
tory bolt. Reinstall the Factory engine and shock tower
covers .Note: These steps must be performed in order
to avoid difficulty with bolt hole alignment.
Reconnect the negative battery cable
.
A
Do not install bolt in bracket un-
til step 16.
10. Transfer the air sensors from the Factory air box lid
into the Airaid intake tube(#2). Do not use factory
hardware! Secure the MAF sensor using the two #8-
32x 1/2 screws (#16) and Lock Washers (#17), and the
MAP sensor with the 1/4-20x3/4 bolt (#19).Install the
Reducer Coupler and one #64 clamp(#26) and the #48
(#27) clamp on the 90 deg bend of the Intake Tube.
Install the Hump Hose (#9) and 2 #64 clamps(#26) on
the opposite end of the Intake Tube.
MAF and MAP
C
B
Do not install bolt in bracket un-
til step 16.
B
12. A) Lower the Airaid Performance Air box assembly
into the engine cavity . Insert the Well Nut into the Fac-
tory core support grommet and rotate the assembly rear-
ward until the bracket rests on the shock tower and the
MAF panel’s lower tab hole is lined up with the Tapped
Chassis bolt hole from step 5. B) Secure the assembly
by using the 1/4-20x 3/4 Bolt(#19).
Weather strip
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.
FILTER IDENTIFICATION
700-495 Airaid Oiled Media 701-495 Airaid SynthaMax Dry Media - Red
702-495 Airaid SynthaMax Dry Media - Black 703-495 Airaid SynthaMax Dry Media - Blue