Airaid 200-197 User Manual
Page 2
16. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.
17. Reconnect the negative battery cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.15.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
10. Install the Airaid CAD into the vehicle replac-
ing the factory airbox. Secure the CAD using four
M6 x 1.25 Hex Bolt (#15), and 1/4” flat washers
(#14). Do not over tighten the four bolts.
11. Reinstall the MAF sensor onto the filter
adapter, and tighten the clamp.
12. Install the urethane hump hose (#6), and two
#64 hose clamps (#16) onto the MAF sensor as
shown. Tighten only the clamp on the MAF sen-
sor at this time.
13. Install the 1/4” NPT x 3/8” Barb Fitting (#17)
into the Airaid Intake Tube as shown. Next install
the urethane coupler (#7) onto the throttle body
end of the tube using two #64 hose clamps (#16).
Tighten only the clamp on the tube.
14. Install the Airaid Intake Tube into the hump
hose first, and then onto the throttle body. Adjust
it for fit, and tighten the hose clamps. Next install
the 3/8” x 14” breather hose (#8) between the
1/4” NPT x 3/8” barbed fitting in the tube, and
the factory port on the valve cover.
15. Install the Airaid Premium Filter (#1) onto the
air filter adapter, and tighten the hose clamp. Next
install the provided weather strip (#9) onto the top
of the CAD. For ease of install, start at the inner
fender, and work your way towards the radiator.
Reinstall the beauty cover.
WARNING! If your vehicle has a Vehicle Emission Contr ol Infor mation decal affixed to the factor y air -
box, a new replacement label must be obtained and installed in a readily visible position in the engine compart-
ment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be
affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a paint-
ed surface is recommended.
FILTER IDENTIFICATION
700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red
702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.