Airaid 200-195 User Manual
Page 2
16. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and
screws are tight.
17. Reconnect the negative battery cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.14.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
10. Install the Airaid Intake Tube onto the CAD
using two 1/4-20 x 1/2” button head bolts (#7)
and 1/4” flat washers (#8), threaded up from the
bottom of the CAD.
11. Install the assembled CAD into the vehicle by
lowering the front into the vehicle first, and then
aligning the two grommets on the studs at the rear
of the engine. Push down firmly on the rear of the
CAD to seat the gr ommets. Next slide the facto-
ry rubber elbow onto the Airaid Intake Tube.
12. Install the small factory grommet removed in
step #5 into the supplied bracket (#14). Next slip
the installed grommet over the stud on the front
of the engine, and bolt the bracket to the CAD
using one 1/4-20x 1/2” button head bolt (#7), 1/4”
flat washer (#8), and 1/4” serrated nut (#9).
13. Slide the Mass Air Flow sensor connector
thru the hole in the side of the CAD, and install
the “split” grommet (#16) over the wiring loom as
shown.
14. Re-connect the wiring connector to the MAF,
and then seat the large grommet into the hole in the
side of the CAD.
15. Install the Airaid Premium Filter (#1) onto the
Airaid Intake Tube, and tighten the clamp. Install
the weather strip (#6) on top of the CAD starting
at the front corner, and working your way to the
other corner. Reconnect the factory fresh air tube
to the CAD, and tighten the hose clamp. Adjust
the factory rubber elbow on the Airaid Intake
Tube, and tighten the hose clamp.
WARNING! If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a new replacement label must
be obtained and installed in a readily visible position in the engine compartment in order to remain CARB compliant. Failure to do so will prevent
the vehicle from passing a smog check. Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall
not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted surface is recommended.
FILTER IDENTIFICATION
720-440 Airaid Oiled Media
721-440 Airaid SynthaMax Dry Media - Red
722-440 Airaid SynthaMax Dry Media - Black 723-440 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.