Airaid 200-145 User Manual
Page 2
13. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.
14. Reconnect the negative battery cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.13.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
10. Install the urethane hump hose (#6)
onto
the Airaid Intake Tube (#5) and the MAF sen-
sor with two #60 hose clamps (#15). Install
the tube assembly onto the engine. (Hint: slide
the hump hose all the way onto the end of the
tube.)
11. Reconnect the wiring harness to the
MAF sensor .
12. Press the weather strip (#8) along the top edg-
es of the Airaid Cool Air Dam; assure that it is
fully seated along the edges. (Hint: Begin at a
corner and work toward the ends). Mount the
Airaid Premium Filter (#1) onto the air filter
adapter and tighten the hose clamp.
Note: Provisions have been made to mount the factory filter minder if you choose. A 17mm hole must be drilled on the back side of the tube. A circular impression on the
rear of the tube indicates the correct location for the hole. Use the factory grommet to mount the filter minder.
WARNING! If your vehicle has a Vehicle Emission Contr ol Infor mation decal affixed to the factor y air box, a new r eplacement label must be obtained and installed
in a readily visible position in the engine compartment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replacement
labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed to any equipment which is easily detached from the vehicle. Label
placement, under the hood on a painted surface is recommended.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or
instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive
through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-469 Airaid Oiled Media
701-469 Airaid SynthaMax Dry Media - Red
702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.
7. Install the air filter adapter (#4) using three ¼-
20x ½” button head bolts (#12), and 1/4” flat
washers (#13). Position the Airaid Cool Air Dam
in place of the factory airbox & secure it with
four M6-1x25 hex bolts (#14) and 1/4” flat
washers (#13).
8. Slide the factory MAF sensor onto the air
filter adapter and tighten the hose clamp.
(Note: factory clamp / rubber bushing must be
in place on the inlet to the MAF sensor.)
9. Install the GM coupler (#7) onto the throt-
tle body side of the Airaid Intake Tube (#5).