Port configuration, Port configuration -3 – Verilink HDM 2180 (880-503048-001) Product Manual User Manual

Page 21

HDM 2180 Quick Set-Up

Verilink HDM 2180 User Manual

2-3

Figure 2-2 NCM Main Menu

From the NCM Craft interface Main Menu (

Figure 2-2

), select the

HDM application module using option S, Shelf/Slot. The Main Menu
uses brackets to enclose the T, indicating the HDM is now the
active module.

Port Configuration

From the Main Menu, select option C, “Configuration”, to start the
configuration task. The Configuration Menu displays (

Figure 2-3

The Configuration Menu is used to enable—or put in service—each
of the ports and to configure the various port parameters.

-- VERILINK NCM CONTROLLER : FW Rev 4.18c, Feb 6 1998 15:51:38 --

-- VERILINK NCM CONTROLLER : FW Rev 4.18c, Feb 6 1998 15:51:38 --
Site Name: Access Level: 2

Site Name: Access Level: 2

Site Name: Access Level: 2
Managing at NEAR end node [127.255.255.0] Node ID: 20

Managing at NEAR end node [127.255.255.0] Node ID: 20

Managing at NEAR end node [127.255.255.0] Node ID: 20
<- SLOT ->

<- SLOT ->

<- SLOT ->
SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13

SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13

SHELF 1 2 3 4 5 6 7 8 9 10 11 12 13
0 - - - - - - - - - - - - -

0 - - - - - - - - - - - - -

0 - - - - - - - - - - - - -
1 D [T] *N

1 D [T] *N

1 D [T] *N
2 - - - - - - - - - - - - -

2 - - - - - - - - - - - - -

2 - - - - - - - - - - - - -
3 - - - - - - - - - - - - -

3 - - - - - - - - - - - - -

3 - - - - - - - - - - - - -
4 - - - - - - - - - - - - -

4 - - - - - - - - - - - - -

4 - - - - - - - - - - - - -
KEY: A=DIDCSU, B=DIU/DBU, C=CSU, D=DIU, E=SDIU, F=DIU/DDS, G=DHDM,

KEY: A=DIDCSU, B=DIU/DBU, C=CSU, D=DIU, E=SDIU, F=DIU/DDS, G=DHDM,

KEY: A=DIDCSU, B=DIU/DBU, C=CSU, D=DIU, E=SDIU, F=DIU/DDS, G=DHDM,
H=ATM/IMUX, I=IDCSU, J=PEP, K=DAC, L=HLM, M=IMUX, N=NCM, P=DPRI,

H=ATM/IMUX, I=IDCSU, J=PEP, K=DAC, L=HLM, M=IMUX, N=NCM, P=DPRI,

H=ATM/IMUX, I=IDCSU, J=PEP, K=DAC, L=HLM, M=IMUX, N=NCM, P=DPRI,
Q=QUAD, R=SUBRATE, S=HSM, T=HDM, U=DCSU, V=VCU, X=QPRI

Q=QUAD, R=SUBRATE, S=HSM, T=HDM, U=DCSU, V=VCU, X=QPRI

Q=QUAD, R=SUBRATE, S=HSM, T=HDM, U=DCSU, V=VCU, X=QPRI
S) shelf/slot O) administration

S) shelf/slot O) administration

S) shelf/slot O) administration
C) configuration D) diagnostics

C) configuration D) diagnostics

C) configuration D) diagnostics
P) performance/status F) display far end DS3 port identification

P) performance/status F) display far end DS3 port identification

P) performance/status F) display far end DS3 port identification
B) circuit manager A) alarm

B) circuit manager A) alarm

B) circuit manager A) alarm
R) remote end setup I) manufacturing info

R) remote end setup I) manufacturing info

R) remote end setup I) manufacturing info
X) exit this screen

X) exit this screen

X) exit this screen
A [127.255.255.0] [1,1] HDM 2180 >

A [127.255.255.0] [1,1] HDM 2180 >

Menu Heading Area

Node “Map” (Physical

Location of Modules)

Command List

Firmware Version and Date of Release

Access Level (1-4)

Node Address

Data (Command) Entry Area

Module Key

Active NCM Master Designator

❷ ❸

❶

❷
❸

❶

Brackets around module letter ( [T] ) indicate current module selected

Indicator for the type of shelf: M = Multi-line, Q = Quint-line, D = Dual-line

Asterisk indicates that the NCM is the Main Controller in the shelf