Legrand MKFOB - Manual (Page 6)

Fcc Notice
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Caution: Any changes or modifications to this device not
explicitly approved by the manufacturer could void your
authority to operate this equipment.
TESTING
After completing the MKFOB setup, you can test scene recall
by pressing a button. You should hear a soft click when
you press each button. Scene recall works best with an
immediate release of the button. The LED should come on
and be green then turn off a second or two after you release
the button.
TROuBLESHOOTING
During Set House ID, the LED is not flashing on some
Wireless devices.
• If an LED is solid green before initiating house ID binding:
The device already has another house ID. Reset
it to the factory default so that it can be bound to
the desired house ID. Resetting to factory defaults
is described in the “I need to start over” issue.
• If LED is solid yellow after initiating house ID binding:
The device may be out of range of the initiating device.
Move the MKFOB closer to the initiating device. It may
be necessary to add a MRR2 Repeater if reception
to a particular area of the house is blocked.
The LED does not light when I press a button.
The battery may be out of position or
may need replacement. See Battery
Usage/Installing a New Battery.
The MKFOB won’t accept the House ID binding and it will
not initiate a binding.
See “There is no click ...” below.
There is no click when I press a button.
The key membrane inside the MKFOB housing may be
out of position. Contact technical support for assistance.
A device that is included in a scene does not respond
appropriately when I invoke the scene from the MKFOB.
The non-responsive device may be out of range of
the MKFOB. Move the MKFOB closer to the device
and invoke the scene from the MKFOB. If the
device responds appropriately from this distance,
it may be necessary to install an MRR2 Repeater
at a location that is within range of the location
from which the MKFOB is typically operated.
I need to start over.
You can reset any wireless device to factory default settings
by pressing and holding its binding activation buttons until
its LED changes to solid yellow (approximately 10 seconds).
For the MKFOB, the binding activation buttons are 1
and 2. During the process, the LED flashes yellow and
when the reset is complete, it changes to solid yellow.
The yellow LED stays lit for approximately one minute
as it waits to hear a binding message. The device can
then be reconfigured, exactly like any new device.
To set the House ID in the MKFOB, initiate a binding
from any previously bound device in the house.
Please
Recycle
WARRANTY INFORMATION
Manufacturer warranties its products to be free of
defects in materials and workmanship for a period
of five (5) years. There are no obligations or liabilities
on the part of manufacturer for consequential
damages arising out of, or in connection with, the
use or performance of this product or other indirect
damages with respect to loss of property, revenue or
profit, or cost of removal, installation or reinstallation.
Legrand Customers contact: Vantage Customers contact:
1061 South 800 East
Orem, UT 84097
Phone: 800.555.9891
www.vantagecontrols.com
301 Fulling Mill Road Suite G
Middletown, PA 17057
Phone: 800.321-2343
www.legrand.us/onq
07071r2 1/2008