Legrand WSLV700TC Incandescent Dimmers - Manual

MULTIPLE GANGING OF DIMMERS & OTHER DEVICES
Any combination of dimmer models and other devices may be ganged
together. Break off tabs are provided on the 1100 W dimmer straps for multi-
gang applications. Pry off the tabs using pliers before installation, as shown in
the figure. De-rate the maximum load according to the following table:
DIMMER MAXIMUM
MULTI-GANG DE-RATING
CATALOG # LOAD 2 GANG INSTALLATION 3 GANG INSTALLATION
WS1103P 1100 W 900 W 800 W
WS1100 1100 W 900 W 850 W
Note: The 700W dimmers do not require de-rating for multi-gang applications.
REMOVE ALL FINS
2 GANG INSTALLATION 3 GANG INSTALLATION
REMOVE INSIDE FINS ONLY
WARRANTIES
Lifetime Warranty. The device you have purchased is warranted under normal use against
defects in workmanship and materials for as long as you own the device. If the device fails
due to manufacturing defect during normal use, return the device for replacement to the
store where purchased or send to:
Pass & Seymour Legrand
50 Boyd Avenue
Syracuse, NY 13209
All requests for replacement must include a dated sales receipt (legible copies acceptable).
ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
TO A PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. YOUR SOLE AND
EXCLUSIVE REMEDY AGAINST PASS & SEYMOUR LEGRAND UNDER ANY WARRANTY
SHALL BE THE EQUIVALENT REPLACEMENT OF THE DEVICE. IN NO EVENT SHALL
ANY WARRANTY APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION OF THE
DEVICE, IMPROPER WIRING, IMPROPER INSTALLATION, MISUSE, ABNORMAL USE
OR NEGLIGENCE. IN NO EVENT SHALL PASS & SEYMOUR LEGRAND BE LIABLE FOR
LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow limitations on how long implied warranties last and
do not allow exclusion or limitation of incidental or consequential damages. Some of the
above limitations or exclusions may not apply to every purchaser.
Para ser instalado por electricista certificado u otra persona capacitada.
ADVERTENCIA: Para prevenir una sacudida eléctrica severa o electrocución,
siempre CORTE la electricidad en el panel de servicio antes de instalar esta
unidad, trabajar en el circuito, o cambiar una lámpara.
AVISO: Para evitar el recalentamiento y los posibles daños a otro equipo, no
instale este dispositivo para controlar un tomacorriente, una lámpara o tubo
fluorescente, un electrodoméstico a motor o un electrodoméstico alimentado
por un transformador.
No use el reductor de luz con lámparas incandescentes cuyas requisitos de
potencia exija la potencia máxima (indicada en Wats) del reductor de luz.
No conecte al reductor de luz a otra fuente de potencia que no sea solo
120VAC, 60Hz.
Una carga mínima de 40W es requerida.
Solo utilice cables de cobre.
Nota: Puede entrar yeso, polvo o pintura y dañar este dispositivo. No
instalar este dispositivo hasta después de haber instalado y pintado la
pared.
INSTRUCCIONES:
1. Si se suministró un kit de cambio de color, y se desea un color diferente,
vea el Procedimiento de Cambio de Color; de lo contrario, proceda al paso
#2.
2. Corte la electricidad al circuito en el panel quitando el fusible o APAGANDO
el interruptor automático antes de la instalación.
3. Quite la chapa de pared y los tornillos de montura de chucho, hale el
chucho existente de la caja embutida en la pared.
4. Desconecte el chucho existente del circuito. Instalación de tres direcciones:
Identifique el cabe “COMÚN” (el cable conectado al la terminal marcada
“común – common” o la terminal colorada con un color singular). Para
instalación “nueva” identifique el cable conectado al la fuente de potencia
o a la carga.
5. Conecte el reductor de luz como mostrado en el diagrama de instalación
utilizando alambre trenzado o sólido #12 o #14 AWG de cobre. Pele el
alambre utilizando la guÌa en la parte trasera del aparato.
DIAGRAMA DE INSTALACIÓN PARA ATENUADORES
INSTRUCCIONES DE INSTALACIÓN
Serie Perilla Deslizable Ancha
REDUCTORES DE LUZ INCANDESCENTE
INSTRUCCIONES EN ESPAÑOL
L E A Y G U A R D E E S T A S I N S T R U C C I O N E S
To be installed by a certified electrician or other qualified person.
WARNING – To prevent severe shock or electrocution, always turn power
off at the service panel before installing this unit, working on the circuit, or
changing a lamp.
Caution – To reduce the risk of overheating and possible damage to other
equipment, do not install incandescent dimmer to control a receptacle, a
fluorescent light or bulb, a motor-operated appliance, or a transformer-
supplied appliance.
Do not use dimmer with incandescent lamps whose power requirements
exceeds maximum power (stated in Watts) of the dimmer.
Do not connect dimmer to power source other than 120VAC, 60 Hz only.
A 40W minimum load is required.
Use copper wire only.
Note: Sheet rock, dust and paint can enter and damage this device. This
device should be installed after sheet rocking and painting are completed.
COLOR CHANGE PROCEDURE/PROCÉDURE DE CHANGEMENT DE
COULEUR/PROCEDIMIENTO DE CAMBIO DE COLOR
DIRECTIONS
1. If a color change kit was provided, and a different color is desired, see the
Color Change Procedure, if not proceed to step #2.
2. Disconnect power to circuit by removing fuse or turn circuit breakers OFF
before installing.
3. Remove wall plate and switch mounting screws, pull existing switch from
wall box.
4. Disconnect existing switch from circuit. 3-way installation: Identify the
“Common” wire (wire connected to the terminal marked common or odd
colored terminal). For “new” installation identify wire connected to power
source or to the load.
5. Connect dimmer as shown in the installation diagram using #12 or #14
AWG stranded or solid copper conductors. Strip wire using gauge on back
of device.
INSTALLATION DIAGRAM FOR DIMMERS
6. Install dimmer in wall box, with word ‘TOP’ on the strap right side up, using
mounting screws provided.
7. Attach wall plate, then restore power to circuit.
NOTE: It is normal for the dimmer to feel warm during operation. Use a separate
neutral wire for each phase of a multiphase system containing a dimmer, and
for high power single phase applications where flickering is present.
INSTALLATION INSTRUCTIONS
Wide Slide Series
INCANDESCENT DIMMERS
R E A D A N D S A V E T H E S E I N S T R U C T I O N S !
1. 2.
3. 4.