Key fob set-up instructions – Legrand MKFOB User Manual

Page 4

KEY FOB SET-uP INSTRuCTIONS:

Prior to setting up the key fob:
• Install your Top Dog enabled wireless devices (dimmers,

switches, plug-in modules, scene controllers, etc.).

• Configure your Top Dog enabled wireless system (including

scene setting if you have scene controllers in the system)

following the directions provided with each device.

• We recommended that you also read the Miro Installation

Manual, which is available online.

Now you can set up the key fob to work within the wireless

system by simply setting the House ID and Setting the Operating

Mode. If your system does NOT include a scene controller, see

the Application Note titled “Easy Setup Without a House Scene

Controller,” which is available online.

Set House ID

All Top Dog enabled wireless devices installed in the same home

must acquire the same unique House ID before use. This process

is called house binding. Each device is bound to all other Top Dog

enabled wireless devices in the house. The following sequence

assumes that the other devices in the house have already

received the House ID.
1. Momentarily press any button on the MKFOB. The LED

should be solid yellow/amber (a combination of green

and red) and should remain lit for about one minute. This

indicates that it has not yet acquired a House ID; proceed

to step 2. If the LED is a color other than yellow* see

Troubleshooting.

2. Go to any device already bound to the house (identified

by a solid green LED) and initiate binding by pressing the

binding activation keys until its LED flashes yellow (about

2 seconds). Binding is typically initiated by simultaneously

pressing and holding the top and bottom of a paddle-

operated device.

3. If the LED on the MKFOB is still lit when you complete the

previous step, it turns green when it receives the House ID,

then it begins flashing green.

If the LED on the MKFOB is not lit, press and hold any button

until the LED turns green indicating that it received the

House ID.

4. Return to the same device used to initiate the binding and

end the binding by pressing the binding activation keys until

the device LED changes to solid green (about 2 seconds). All

device LEDs should now be solid green.

Set the MKFOB Operating Mode

Review the following sections that describe Operating Mode-1,

Operating Mode-2 and Operating Mode-3. Choose the operating

mode that you wish to use. Note that each operating mode

recalls specific scenes. For example, Operating Mode-1 (default)

recalls house scenes 1, 5, and 11 from buttons 1, 2, and 3.

LED

Buttons
1
2
3

Key-chain loop

Operating Mode-1 (Default)

In Mode-1, the MKFOB is

bound to the house. Mode-1

is used to recall and record

House scenes 1, 5, and 11.

Scene 11 is the scene that

executes when you press

the bottom of the ON/OFF

paddle on a house level

controller, which has a

default operation of turning

off all devices bound to the

house.

MODE-1

Button

Recall

House Scene 1

House Scene 5

House Scene 11 (bottom of house controller paddle)

Use the procedure below to set the MKFOB to Mode-1.
1. Start binding from the MKFOB: Simultaneously press

and hold button 1 and 2 until the LED starts flashing

yellow (approximately 2 seconds).

2. Press and hold MKFOB button 1 until the LED

changes to green then starts flashing yellow again

(approximately 2 seconds).

3. End the binding from the MKFOB: Simultaneously press

and hold button 1 and 2 until the LED stops flashing

yellow and turns green (approximately 2 seconds).

Operating Mode-2

In Mode-2 the MKFOB

is bound to the house.

Buttons 1 and 2 are the

same as Mode-1 but button

3 is used to toggle PANIC

mode (scene 14). In other

words, a press of button

3 toggles the command

that is issued by the device

from Over-Ride to Scene

14 (Panic) to Revert Over-

Ride in order to restore the

home to the previous state.

MODE-2

Button

Recall

House Scene 1

House Scene 5

Panic/Cancel Panic (Toggle house scene 14)

Use the procedure below to set the MKFOB to Mode-2.
1. Start binding from the MKFOB: Simultaneously press

and hold button 1 and 2 until the LED starts flashing

yellow (approximately 2 seconds).

2. Press and hold MKFOB button 2 until the LED

changes to green then starts flashing yellow again

(approximately 2 seconds).

3. End the binding from the MKFOB: Simultaneously press

and hold button 1 and 2 until the LED stops flashing

yellow and turns green (approximately 2 seconds).

LED

Scene

MKFOB
Mode-1

LED

Scene

MKFOB
Mode-2