Legrand TITAN Series v.2 - Manual (Page 3)

MULTI GANG INSTALLATION INSTRUCTIONS
FINS ARE NOT REMOVED
NOTE: A 3-gang Installation of Narrow Dimmers is shown and described
below. Any Combination of Wide and Narrow Dimmers will gang the same way.
1. Select the correct box size from Table 6.
Table 6 – Wall-box Gang Requirements – FINS are NOT REMOVED
3. Connect the dimmer as shown in the wiring diagram using the appropriate
sized wire connectors.
4. With the word “TOP” up, install dimmer in the wall box using mounting
screws provided (leave mounting screws “finger tight” at this point).
5. Attach the Couplers between the Dimmers with the screws that were
removed in step 2.
Remove this screw to remove End Cap
End Cap
Remove this screw to remove End Cap
*Wall Box Requirements for Ganging an Even Number of Narrow Dimmers.
4+1 set up shown below:
Chase nipple
4-gang
wall box
1-gang
wall box
2.712
Narrow Dimmers
0 1 2 3 4 5 6
0 0 1 1+1* 4 4+1* 7 7+1*
1 1 3 5 6 8 9 11
2 4 5 7 8 10 11 13
3 6 8 9 11 12 14 15
4 9 10 12 13 15 16 -
5 11 13 14 16 – – -
6 14 15 – – – –
W
id
e
D
im
m
er
s
MULTIPLE GANGING OF DIMMERS
Any combination of dimmer models may be ganged together. Using a vise or heavy-duty pliers, remove the fins on either or both sides of the heat sink, as
necessary. Dimmers can be ganged without removing fins by proper selection and placement of outlet boxes (see Table 6 and Table 7). When Dimmers are ganged,
De-rate the maximum load according to the following De-Rating Table 5:
Table 5 – Derating for Multi-Gang Installations
2. Remove the End Cap between adjacent dimmers (2 screws for each End
Cap). Keep these screws as they will be needed at step #5.
NOTE: The End Cap that is not between dimmers does not get removed.
Fins are NOT Removed Fins are Removed
Dimmer 1-Gang 2-Gang 3- or more Gang 2-Gang 3- or more Gang
Catalog # Installation Installation Installation Installation Installation
CD700 700W 700W 700W 700W 700W
CDLV700 700VA 700VA 700VA 700VA 700VA
CD703P 700W 700W 700W 700W 700W
CDLV703P 700VA 700VA 700VA 700VA 700VA
CD1100 1100W 1100W 1000W 1000W 900W
Narrow CDLV1100 1100VA 1100VA 1000VA 1000VA 850VA
Dimmers CD1103P 1100W 1100W 1000W 1000W 950W
CDLV1103P 1100VA 1100VA 1000VA 1000VA 850VA
CDFB5 5A 5A 5A 5A 5A
CDFB8 8A 8A 8A 7.7A 6.3A
CDFB53P 5A 5A 5A 5A 5A
CDFB83P 8A 8A 8A 7.7A 6.3A
CDSC6 6A 6A 6A 6A 6A
CDDH16 1.6A 1.6A 1.6A 1.6A 1.6A
CD3FB16 16A 16A 16A 16A 16A
CD3FB163P 16A 16A 16A 16A 16A
CD3FB10-277 10A 10A 10A 10A 10A
CD3FB103P-277 10A 10A 10A 10A 10A
CD1600 1600W 1600W 1600W 1600W 1550W
CDLV1600 1600VA 1600VA 1600VA 1600VA 1550VA
CD1603P 1600W 1600W 1600W 1600W 1550W
CDLV1603P 1600VA 1600VA 1600VA 1600VA 1550VA
CD2000 2000W 2000W 2000W
NO FINS TO REMOVE
CD2003P 2000W 2000W 2000W
Wide CDFB10 10A 10A 10A 10A 10A
Dimmers CDFB16 16A 16A 16A NO FINS TO REMOVE
CDFB7-277 7A 7A 7A 7A 7A
CDFB10-277 10A 10A 10A 10A 10A
CDSC12 12A 12A 12A 12A 12A
CDFB103P 10A 10A 10A 10A 10A
CDFB163P 16A 16A 16A NO FINS TO REMOVE
CDFB73P-277 7A 7A 7A 7A 7A
CDFB103P-277 10A 10A 10A 10A 10A
Couplers
6. Tighten the mounting screws, insert the label, attach the wall plate, and
restore power to the circuit.
7. Calibrate the Dimmer if necessary – Refer to Single Gang Installation
Instructions, step #7.
f. Fluorescent Dimmers “CD3FB” Series: No adjustments are required.
The minimum light level is calibrated at the factory and does not
normally require adjustment. If the lamps drop out or flicker at the
minimum dimming level, there may be an installation error.
NOTE: To ensure full lamp life and proper dimming performance, it is rec-
ommended to “season” fluorescent lamps prior to dimming. This is accom-
plished by operating the lamps at maximum light levels for up to 100 hours.
Refer to individual lamp manufacturer for recommended seasoning times.