Cooler connections - 2 of 2 -19, Cooler connections – 2 of 2 – Hypertherm HT4400 HySpeed Plasma Arc Cutting System User Manual
Page 53

INSTALLATION
HT4400
Instruction Manual
3-19
8
Cooler Connections – 2 of 2
ቮ
Hoses - Cooler to Ignition Console
Part No.
Length
128499
5 ft (1.5 m)
028652
10 ft (3.1 m)
028440
15 ft (4.6 m)
028653
20 ft (6.1 m)
028441
25 ft (7.6 m)
128495
30 ft (9.2 m)
128496
40 ft (12.2 m)
028442
50 ft (15.3 m)
Part No.
Length
128052
60 ft (18.3 m)
028443
75 ft (22.9 m)
028444
100 ft (30.5 m)
028747
125 ft (38.1 m)
028445
150 ft (45.8 m)
128064
175 ft (53.4 m)
028637
200 ft (61 m)
Note: There are 2 hoses contained in each
hose set part number listed here.
Green
Green
Red
Red
Adding Coolant to the Cooler
1. Install consumables in the torch: see Changing
Consumables in Section 4.
2. Remove cooler filler cap.
3. Add coolant until level is full on the level gauge.
4. Turn the cooler on for 1 minute and add more
coolant, if necessary.
See Post Installation later in this section.
See also Torch Coolant Requirements earlier in this
section.
Filter cap
Level gauge
Caution
Use Hypertherm coolant (028872) to reduce the risk of damage from
freezing and to prevent long-term corrosion.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)