Analog board pcb3 - status indicators -19, Analog board pcb3 - status indicators – Hypertherm HT4400 HySpeed Plasma Arc Cutting System User Manual
Page 110

MAINTENANCE
HT4400
Instruction Manual
5-19
3
Analog Board PCB3 - Status Indicators
See page 6-2 for location of Analog Board.
Note:
•
D15 Arc transfer output - illuminates when total current sensor (CST) senses a current higher than
30 amps.
•
D11, D12, D13, D17 Chopper outputs - illuminates when each chopper current sensor (CS1-CS4)
senses a current higher than 7 amps.
•
D5 Current Detect from CH1&CH2 - illuminates when both CH1&CH2 output more than 7 amps.
•
D4 Current Detect from CH3&CH4 - illuminates when both CH3&CH4 output more than 7 amps.
D17
Current Detect
from CH1
D15
Arc Transfer
D5
Current Detect
from CH1&CH2
D1
+15 VDC
D4
Current Detect
from CH3&CH4
D13
Current Detect
from CH2
D12
Current Detect
from CH3
D11
Current Detect
from CH4
REC9
REC10
REC5
REC6
REC7
REC3
REC4
See also other documents in the category Hypertherm Equipment:
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)